|
User Manual for Angler 3-Monolight Portrait Back Light Kit with Case Click to enlarge the picture
Contents of the user manual for the Angler 3-Monolight Portrait Back Light Kit
- Product category: Monolights Angler
- Brand: Angler
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Angler Monolights
|
User manual for the Angler 3-Monolight Portrait Back Light Kit contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Angler product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Angler user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Angler product will considerably shorten its lifespan!
|
Product description has put together this Angler 3-Monolight Portrait Back Light Kit with Case to give photographers everything they'll need for a 3-point setup geared for studio work. The kit contains two Angler Glamour Flash 300Ws Monolights, two 43" white translucent umbrellas, and an Impact 100Ws EX100 Monolight with a 24 x 24" softbox. A kit case is provided for the lights. A 2-section, 3' Back Light Stand is included to allow use of one of the flash heads to illuminate the background, and an 8' air-cushioned light stand is included for each of the other two lights. Finally, a PowerTrigger Transmitter / Receiver Set is included to fire the lights wirelessly at distances up to 75'. - 2 x Angler Glamour Flash 300Ws Monolight The Glamour Flash 300Ws Monolight from Angler combines affordability with dependable basic functionality. Power is adjustable from 1/16 to Full power over four stops via touchpad buttons. Settings are displayed on the large LED screen. The 100W modeling lamp can be set from full power for maximum visibility to Proportional to simulate power adjustments to enable previewing of your shot. Recycling is a fast 2 seconds and far shorter at reduced power settings. The Glamour Flash has an industry standard 5/8" receiver that mounts to a wide variety of light stands while the housing is rubber-coated to provide a grippy surface and protection from impact damage. The flash head can be triggered with the head's test button, a built-in wireless optical slave or with the included sync cord. The Glamour Flash comes with a user-replaceable flash tube, power cord, 100W modeling lamp, 7" grid reflector and a protective cap.
- LED Screen
- Highly visible LED screen makes the power setting adjustment easy even in dim light
- Adjustable Power
- Power is adjustable from over 4 stops from 1/16 to Full power
- Touchpad Control
- Easy to use touch pad instead of switches
- Modeling Lamp
- Full on mode can be adjusted to proportional mode that automatically matches the flash power so you can preview your lighting
- Auto Dump
- Flash automatically drains capacitors for accurate exposures when lowering the power
- Rubber Coating
- Provides a grippy surface and helps protect the flash from impact damage
- Optical Slave
- Good for multi-light setups, the built-in slave allows the flash to be wirelessly triggered from another flash
- Included Sync Cord
- The 1/8" (3.5mm) mini-plug sync cord connects camera to flash or optional radio receiver
UPC: 847628589247 - Impact One-Monolight Kit (120 VAC) The Impact One-Monolight Kit (120 VAC) is an economical 100-watt/second monolight with modeling light and power variator. This kit includes a softbox with mounting ring, to soften the light output.
- The included 24 x 24" softbox has a silver interior for crisper highlights.
- PC sync cord with monoplug is included.
- Line sync voltage is only 4.3 VDC (safe for any camera's circuitry).
UPC: 847628011243 - Impact Two Section Back Light Stand (3') This 3' Impact Back Light Stand consists of a base and riser. Use the lower part as a base to place a mounted light at floor or table level, as low as 5.5". Add the extension to the base to raise the height of the light from 22.8" (57.9 cm) to a maximum of 3' (90 cm). The stand is constructed of black anodized aluminum.
- Quick Set Up
- Sets up easily in the matter of seconds
- Very Stable
- Stable under recommended loads
- 5/8" Reversible Stand Mount
- Fitted with a reversible 5/8" top stud, with 1/4"-20 and 3/8" threads
UPC: 847628011939 - 2 x Impact White Translucent Umbrella (43") Umbrellas soften, broaden, and diminish the light output of any flash light source. Umbrellas with a white interior will soften and weaken light more than an umbrella with a silver lining. A white umbrella without a black backing may also be used as a makeshift softbox, although the use of the light will not be as efficient as with a lightbox.Choosing umbrella size is determined by the size of the subject, and the strength of the light supply being used. Choosing an umbrella surface is as subjective as choosing a paint and brush.This Impact 43" White Translucent Umbrella is suggested for use in mid-length portraits for one or two persons. UPC: 847628013292
- Impact Light Kit Bag #2 (34 x 13.5 x 12") The black Light Kit Bag #2 (34 x 13.5 x 12") from Impact makes transporting your lighting kit easy and secure. The bag is designed to hold three monolights along with their reflectors (such as Impact VC500LR), four stands, boom, umbrellas, cables and other support gear but can also be used to hold other lighting equipment instead. You'll have plenty of room to take along enough lighting gear for a portrait session - all packed in an organized and accessible way. A touch fastened divider tray separates the stands, boom and umbrellas from the lights preventing them from bumping together and causing scratches or damage. For additional smaller equipment such as cables and small accessories, there are three interior 10.5 x 8.0" zippered mesh pockets.The bag is made from soft, padded water-resistant nylon and contains six movable touch fastened interior dividers (6 large, 2 small) that will permit you to configure the bag to accommodate the gear you need that day. The Light Kit Bag is carried by its two 2" wide overlapping top carry handles that can easily be extended into dual shoulder straps. The contents are accessed via dual zippers that when placed together will accept a user-supplied lock. For even more protection, the bottom of the bag contains three rubber feet for when the bag is placed on the ground. And the bag folds down to a quarter of its height for convenient storage and easy setup. Whether for storage or transport, the Impact Light Kit Bag will serve both pro or amateur well.
- The soft padded carry case is designed to hold three monolights with reflectors, four light stands, umbrellas, cables and other accessories
- The interior has six movable, touch fastened dividers that permit you to configure the bag to suit your needs; dividers consist of six large and two smaller styles
- 2" (5.1 cm) wide overlapping dual carry handles that convert to a shoulder strap
- Interior has three zippered 10.5 x 8.0" mesh pockets (26.7 x 20.3 cm)
- Touch fastened protective nylon tray separates light stands and umbrellas from monolights
- Water-resistant padded nylon construction
- Folds down to less then 4" for convenient storage and easy setup
- Dual zippered opening; accepts user-supplied lock
UPC: 847628030619 - 2 x Impact Air-Cushioned Light Stand (Black, 8') This aluminum Impact Air-Cushioned Light Stand rises to a height of 8' and folds down to 29.6". The stand has sure-twist section locks and 4 sections and will support up to 8 lb. If you forget to tighten any section with your light mounted, the light slowly descends, thanks to the air-cushioned action. This useful feature saves equipment and fingers from harm during busy photo sessions.
- Air Cushioned
- Protects equipment from impact damage.
- Compact Design
- Will fit easily into most location cases.
- Accepts Casters
-
- Eases positioning of heavy lights.
- Available as accessories.
UPC: 847628012349 - Impact PowerTrigger 16 Channel AC Transmitter and Receiver Set The PowerTrigger 16 Channel AC Transmitter and Receiver Set from Impact contains everything you'll need to wirelessly trigger your studio AC flash units at distances up to 75'. The set includes a 16 channel transmitter and receiver as well as a 2.5mm sub-mini to PC cable, a 3.5mm to 1/4" monoplug adapter and a pre-installed battery for the transmitter.The low-profile 1.2 x 1.6 x 2.8" PowerTrigger transmitter has a hot shoe for your camera, a test button, and 16 separate channels operating on the 433 MHz frequency to prevent interference from other devices. Channels are chosen on both the transmitter and receiver by configuring 4 DIP switches in 1 of 16 permutations on both the transmitter or receiver for wireless triggering from up to 75' away with flash sync speeds of up to 1/200 second. The transmitter runs on a pre-installed, 23A battery that can last up to 2 years with normal use.Unlike the transmitter, the PowerTrigger receiver doesn't use batteries and is instead powered by the same AC cord that's used for your monolight. Think of it as an in-line receiver. Simply plug the end of the power cord into the receiver then plug the receiver's power cord into the head's power outlet. Finally, plug the PowerTrigger's attached 3.5mm sync cable into the flash. A 1/4" mono plug adapter is provided if the head doesn't have 3.5mm input. If you don't know what your flash head's sync voltage is, or if you're using an older unit you might want to purchase a Wein Safe-Sync adapter (MFR# 990-510) to insure that the sync voltage remains under 6V. The Safe Sync's monoplug attachment can be easily adapted to 3.5mm if necessary.
- 433 MHz Radio Signal
- Using a powerful radio signal allows you to trigger your studio flash without line of sight positioning
- Flash Sync Speed of up to 1/200 Sec.
- Take advantage of sync speeds up to 1/200 of a second with compatible cameras
- Wireless
- Cable-free triggering allows you to activate a studio flash from up to 75' (22.8 meters) away without a physical connection
- 16 User-selectable Channels
- Multiple channels allow you to change your receiver settings to avoid interference from other wireless devices
- LED Indicator
- Confirms sending/receiving signals, and active AC power
- Multi-voltage
- 100-230 VAC, 50/60 Hz
- Long-lasting Transmitter Battery
- Included user-replaceable 12V 23A alkaline battery lasts up to 2 years
UPC: 847628579507 In the Box - 2 x Glamour Flash 300Ws Monolight efxzrattsvzq
- Modeling Light (100W)
- Grid Reflector (7")
- Mini to PC Sync Cord
- Protective Cap
- User Manual
- Limited 1-Year Warranty
- Impact - One-Monolight Kit (120 VAC) efxzrattsvzq
- Impact - Two Section Back Light Stand (3')
- 2 x Impact - Umbrella - White Translucent (43")
- Impact - Light Kit Bag #2 (34 x 13.5 x 12")
- 2 x Impact - Air-Cushioned Light Stand (Black, 8')
- Impact - PowerTrigger 16 Channel AC Transmitter and Receiver Set
Table of Contents
|
Upload User Manual
Have you got an user manual for the Angler 3-Monolight Portrait Back Light Kit with Case in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parameters - 2 x Angler Glamour Flash 300Ws Monolight
| Maximum Power | 300 Ws | Power Control | 4 Stops in 1/10-Stop Increments | Guide Number | 180.4' / 55 m at 6.56' / 2 m, ISO100 with Reflector | Flash Duration | 1/1800 to 1/800 Sec | Recycle Time | 2 Sec (Full Power) | Color Temperature | 5600K ± 200K | Flash Ready Indicator | Audio, Visual | Reflector | Changeable | Accessory Fitting Type | Bowens S Type | | Type | Tungsten | Wattage | 100 W | Control Modes | Full On, Proportional | | Sync Type | Button, Cable, Optical | Sync Voltage | 4.3 V | | AC Input Voltage | 110to120 VAC, 60 Hz | Circuit Protection | Fuse | Fuse | 6 A | | Display | None | Mount | 5/8" / 16 mm Receptacle | Auto Dump | Yes | Fan Cooled | No | Dimensions | H: 8.4 x W: 6.1 x L: 11.6" / H: 21.3 x W: 15.5 x L: 29.5 cm, Including Reflector H: 8.4 x W: 5.2 x L: 11.6" / H: 21.3 x W: 13.2 x L: 29.5 cm, Including Cap | Weight | 3.5 lb / 1.58 kg | | Box Dimensions (LxWxH) | 21.5 x 10.5 x 6.5" | - Impact One-Monolight Kit (120 VAC)
| Maximum Power | 100 Ws | Flash Duration | 1/1500 to 1/1000 Sec | Recycle Time | 3 Sec (Full Power) | Flash Ready Indicator | Visual | Reflector | Changeable | Accessory Fitting Type | Elinchrom Umbrella Shaft | | Type | Tungsten | Wattage | 60 W | | AC Input Voltage | 120 VAC, 60 Hz | Circuit Protection | Fuse | | Display | None | Auto Dump | No | Fan Cooled | No | Dimensions | H: 7.8 x W: 5.0 x L: 9.5" / H: 19.7 x W: 12.7 x L: 24.1 cm | Weight | 2.6 lb / 1.2 kg | | Box Dimensions (LxWxH) | 23.2 x 9.5 x 7.3" | - Impact Two Section Back Light Stand (3')
Load Capacity | 7 lb / 3.2 kg | Mounting Options | 1/4"-20 Male Thread 3/8"-16 Male Thread 5/8" Receiver 5/8" Stud | Number of Sections | 2 | Maximum Working Height | 3' / 0.9 m | Minimum Working Height | 5.5" / 14 cm | Collapsed Height | 20" / 51 cm | Footprint Diameter | 23.6" / 60 cm | Accepts Wheels | No | Air Cushioned | No | Detachable Base | Yes | Leveling Leg | No | Reverse Legs | No | Finish | Black | Material | Aluminum | Weight | 2.9 lb / 1.3 kg | Warranty Length | Limited 1-Year Warranty | | Box Dimensions (LxWxH) | 20.55 x 3.3 x 3.25" | - 2 x Impact White Translucent Umbrella (43")
Size | 43.0" / 109.2 cm | Interior | White (Translucent) | Shaft Diameter | 8 mm | Folded Size | L: 28.3" / L: 71.8 cm | | Box Dimensions (LxWxH) | 29.0 x 2.7 x 1.65" | - Impact Light Kit Bag #2 (34 x 13.5 x 12")
| Interior Dimensions | 34 x 13.5 x 12" / 86.4 x 34.3 x 30.5 cm | | Closure Type | Zipper | Carry and Transport Options | 2 x Connecting Handstrap | Material of Construction | Nylon | Exterior Dimensions (W x H x D) | 34.5 x 14 x 13" / 87.6 x 35.6 x 33 cm | Weight | 5.8 lb / 2.6 kg | | Box Dimensions (LxWxH) | 35.0 x 14.0 x 12.5" | - 2 x Impact Air-Cushioned Light Stand (Black, 8')
Maximum Load | 8 lb (3.6 kg) | Leg Tip | 20 mm | Attachment Size | 5/8" Stud with 1/4"-20 in threaded tip | Accepts Wheels | Yes | Air Cushioned | Yes | Maximum Height | 96" (243.8 cm) | Minimum Height | 34" (86.3 cm) | Folded Height | 29.6 (75.2 cm) | Footprint Diameter | 36" (91.4 cm) | Weight | 2.05 lb (1 kg) | | Box Dimensions (LxWxH) | 29.75 x 3.2 x 3.15" | - Impact PowerTrigger 16 Channel AC Transmitter and Receiver Set
| Channels | 16 | Wireless Range | 75' / 22.8 m | Radio Frequency | 433 MHz | | Bottom Mount | Transmitter: Hot Foot | | Dimensions | 1.2 x 1.6 x 2.8" / 3.1 x 3.9 x 7.2 cm (Transmitter) | Weight | 1.3 oz / 37 g | | Box Dimensions (LxWxH) | 8.5 x 5.0 x 2.0" |
Rating50% users recommend this product to others. And what about you?
This product has already been rated by 20 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Honeywell Home Doorbell 916.8 MHz Product Ref: 3231665-002 Rev B... Go Pro FETCH Dog Harness ADOGM-001... Trijacon ACOG USMC scope... Pyle Pro BTA 62BT 6-Zone Stereo Receiver Bluetooth... LG Gram 17 Laptop...
|
Discussion |
Latest contributions to the discussion:
lithium ion battery pack EN-EL5 3.7 V 1100mAh Name: Jane Holland Nikon EN-EL5 Lithium-Ion Battery HI:
How can I tell if this (old) battery is still good? I cannot charge it on my old Nikon COOLPIX P500 camera.
Thank You
Jane Holland
... lithium ion battery pack EN-EL5 3.7 V 1100mAh Name: Jane Holland Nikon EN-EL5 Lithium-Ion Battery HI:
How can I tell if this (old) battery is still good? I cannot charge it on my old Nikon COOLPIX P500 camera.
Thank You
Jane Holland... Settings access and setup Name: Edwin Derks Nuance PaperPort 14 I had a problem with Paperport loading. Through the remote efforts of a Tech was able to get back online, however, "settings" are only listed 1 - 5 with no action listed as was 'visibly' available, (i.e. Scan both sides, Black and White, Color, etc.)
1. how to change, 2. wha... query Name: Vudayagiri Balasubramanyam Bose Wave SoundTouch Music System IV how to set up my bose radio with my remote working-class ... Hi. I didn’t even get a chance to try it once! :( plz help Name: Eric Tasakovic Keeley Dark Side Pedal I ordered a dark side pedal second hand online for 20 bucks cheaper than it would have been to buy it new….20 measly bucks. Anyway…it didn’t come with a power supply. I messed up and accidentally plugged in a 9v ac output power supply in, instead of the required 9v dc. I’...
|
|