User Manual for ART TransX Two-Channel Microphone Preamp Click to enlarge the picture
Contents of the user manual for the ART TransX Two-Channel Microphone Preamp
- Product category: Microphone Preamps ART
- Brand: ART
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for ART Microphone Preamps
|
User manual for the ART TransX Two-Channel Microphone Preamp contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any ART product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official ART user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a ART product will considerably shorten its lifespan!
|
Product description The ART TransX is a 1 RU rack-mountable, two-channel microphone preamp designed to deliver up to 68 dB of clean signal amplification for musicians, vocalists, and audio engineers in live stage applications and home, project, and commercial recording studios. Input and output transformers minimize noise and optimize consistency in levels for balanced and unbalanced connections. Each channel features a stepped gain control, output trim, and -20 dB pad for proper management of signal levels. The variable impedance and 12-position, low-cut filters allow tonal fine-tuning. Connect your microphones to the balanced XLR inputs on the rear panel and plug instruments directly into the front-panel Hi-Z 1/4" inputs. Balanced XLR and 1/4" outputs enable proper connectivity with audio interfaces and mixing consoles. Counter hum from improper grounding via the ground-lift switches. 11-segment LEDs provide easy metering of output levels for each channel. The TransX's included 48 VDC external power supply utilizes a locking connector to prevent accidental disconnects. - Low-noise, low-THD discrete audio path
- Input transformer blocks RFI and other noise
- Custom output transformer reduces ground noise and maintains level for balanced and unbalanced connections
- Hi-Z, direct-coupled, low-noise instrument input
- Variable 150 Ohms to 1 kOhm impedance for XLR mic input
- Rotary switches allow for reliable, repeatable results
- Gain and trim controls allow coarse and fine level adjustments
- Selectable -20 dB pad inhibits distortion when accepting strong mic input signals
- 11-segment, peak-sensitive output level LEDs
- Per-channel switches for phantom power, polarity inversion, and ground lift
- Automatic muting on outputs
- Includes 48 VDC external power supply with locking connector
- Rugged rack-mountable steel chassis occupies 1 RU of rack space
UPC: 840402043140 In the Box ART TransX Two-Channel Microphone Preamp 48 VDC Power Supply IEC Power Cable Limited 3-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the ART TransX Two-Channel Microphone Preamp in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersART TRANSX Specs | Number of Channels | 2 | | Inputs | 2 x XLR 3-pin balanced
2 x 1/4" TS unbalanced | | Outputs | 2 x XLR 3-pin balanced
2 x 1/4" TRS balanced | | Phantom Power | +48 VDC, filtered, current limited | | Input Impedance | XLR Input: 150 Ohms to 1 kOhm
1/4" Input: 1 MOhm | | Output Impedance | 100 Ohms | | Maximum Input Level | XLR: +24 dBu
1/4": +15 dBu | | Maximum Output Level | +24 dBu | | Maximum Gain | Mic Input to Balanced Output: +68 dB
Instrument Input to Balanced Output: +59 dB | | Gain Control | +25 to +58 dB | | Frequency Response | 10 Hz to 50 kHz (
Rating50% users recommend this product to others. And what about you?
This product has already been rated by 90 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Call Of Duty World War Two For Xbox...
controller stratus XL...
stratus XL...
smart whatch serie S11 42mm...
Allen & Heath SQ-6 manual...
|
| Discussion |
Latest contributions to the discussion:
AEW R 4100
Name: MAURICIO ANGARITA
Audio-Technica AEW-R4100 UHF Diversity Receiver for
AEW R 4100 has the mute function blocked and does not allow audio to pass. I tried several times to turn off the mute from the transmitter but it does nothing, the mute stays on. Solution?
Thank you...
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
Help needed
Name: Ann Carter
SanDisk 1TB Extreme Portable USB 3.1
When I click the link to download the user manual for my Sandisk Extreme external hard drive, it gives me the manual for the LG Cricket. Can you please change the link so I can download the Sandisk manual and begin using this drive? Thank you....
|
|
