|
User Manual for ATI Audio Inc DDA-212XLR 192 kHz Digital Distribution Amplifier Click to enlarge the picture
Contents of the user manual for the ATI Audio Inc DDA-212XLR 192 kHz
- Product category: Distribution Amplifiers ATI Audio Inc
- Brand: ATI Audio Inc
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for ATI Audio Inc Distribution Amplifiers
|
User manual for the ATI Audio Inc DDA-212XLR 192 kHz contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any ATI Audio Inc product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official ATI Audio Inc user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a ATI Audio Inc product will considerably shorten its lifespan!
|
Product description The DDA-212XLR 192 kHz Digital Distribution Amplifier from ATI Audio Inc. is a dual 1 x 6 AES/EBU digital audio distribution amplifier. Internal dual 1x6 distribution amplifiers allow the unit to operate as 2 independent distribution amplifiers, receiving signal from independent sources and sending the signal to independent zones. An internal jumper can be moved for 1 x 12 operation if necessary (refer to manual).The DDA-212XLR uses 110-Ohm XLR connectors on all inputs and outputs. Sample rates from 27 to 96 kHz are decoded and cleanly regenerated. Standard sample rates of 32, 44.1, 48, 88.2, and 96 kHz are indicated with front-panel numeric readouts. The numeric display also provides signal status and error message information. - Dual 1 x 6 Signal Distribution
- The unit features dual 1 x 6 distribution amplifiers. This allows signal distribution of AES/EBU digital audio from dual independent sources.
- 110-Ohm XLR Connectors
- Transformer-balanced 110-Ohm XLR connectors are provided on inputs and outputs.
- Accurate Regeneration
- The DDA-212XLR will support and accurately regenerate digital audio from 27 to 96 kHz.
In the Box ATI Audio Inc DDA-212XLR 192 kHz Digital Distribution Amplifier Limited 1-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the ATI Audio Inc DDA-212XLR 192 kHz Digital Distribution Amplifier in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersATI Audio Inc DDA212-XLR Specs | Input Connectors | Balanced XLR Female, Paralleled Input Connectors for Loop-Thru Expansion | | Input Level | 200 mV p-p Minimum | | Input Impedance | Transformer Isolated, Balanced and Floating XLR Inputs 110 Ohms | | Sampling Rate | 27 to 96 kHz | | Maximum Cable Length | > 300 m of 110-Ohm Cable with Equalizer Allows Longer Runs | | Clock | With Reclocking on, Regenerated from Input Signal; Clock Jitter < 300 Picoseconds Peak-to-Peak at 96 kHz Sample Rate
With Reclocking Off, Input Clock Is Passed Directly to Outputs | | Clock Jitter | < 3 Nanoseconds Peak-to-Peak | | Output Connectors | 12 x XLR Male Chassis Mount | | Output Level | XLR, 4 V p-p Loaded at 110 Ohms | | Impedance | Balanced XLR 110 Ohms | | Output Jitter | < 300 Picoseconds Peak-to-Peak at 96 kHz Sample Rate | | Propagation Delay | < 25 Nanoseconds | | Power | Internal, 115/230 VAC ±10%, 50/60 Hz, 10 VA. IEC 320 3-Pin Connector | | Dimensions | 19.00 x 1.75 x 8.50" / 48.26 x 4.45 x 21.59 cm | | Weight | 7.00 lb / 3.18 kg | | | | Package Weight | 5.15 lb | | Box Dimensions (LxWxH) | 20.4 x 11.1 x 3.8" |
Rating90% users recommend this product to others. And what about you?
This product has already been rated by 73 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Swan Bread maker SWBBA7...
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
call of duty world war II...
Audio Technica AUDIO-AT8631
data sheet ...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
