User Manual for Axis Communications A1001 Network Door Controller Click to enlarge the picture
Contents of the user manual for the Axis Communications A1001 Network Door Controller
- Product category: Access Controllers Axis Communications
- Brand: Axis Communications
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Axis Communications Access Controllers
|
User manual for the Axis Communications A1001 Network Door Controller contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Axis Communications product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Axis Communications user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Axis Communications product will considerably shorten its lifespan!
|
Product description Axis Communications A1001 Network Door Controller: Redefining Access Control Read More dfrcawaazrczewdyedvrevasxuvycxsuw The A1001 Network Door Controller from Axis Communications gives you a stand-alone digital access control system that can be accessed from anywhere in the world with an internet connection, while offering easy integration with multiple A1001 units, alarm/fire panels, or IP surveillance systems. It uses an open, non-proprietary platform to be compatible with a wide range of hardware and software from many manufacturers. This open platform lets you choose the best products for the location and application, without the constraint of being dependent on a single manufacturer for all of the hardware and software.With Power-over-Ethernet (PoE) compatibility, only a single wire is required for installation, reducing material and installation costs. Readers, locks, relays and request-to-exit (REX) appliances are wired directly to the A1001 for data and power, further reducing the need for long wire pulls to a control panel, and additional power supplies. The fully configurable system features multiple alarm triggers and actions that allow you to tailor the performance of the system to your needs. Access is granted or denied at a group level, and with a fully programmable access schedule you can precisely control when users can access a door. - Flexible Interactivity
-
- Plenum-rated for ceiling/wall mounting above a drop-ceiling
- Non-proprietary, open-platform encourages easy use with third-party software and hardware
- Equipped to work with two readers and to activate two locks, one unit can operate two doors independently
- Unit continues its normal operation locally if there is a network failure
- Supports most reader types and is fitted with configurable input/output ports and controllable power outputs for external equipment such as door locks and contacts
- Web-Based Software
-
- Embedded access-control software in the unit is accessed via web-browsers for use in the same room or building, or from anywhere with an internet connection
- Comes pre-configured for card readers and door monitors, with input triggers and output on/off/pulse
- Fully customizable configurations to tailor to specific needs and equipment
- Access-rights granted at a group level
- Multiple ID types, like a card swipe and PIN, can be required for specific groups or times
- Drag-and-Drop set-up wizard for faster and easier configuration and programming
- Customizable access-schedule for who has access to doors, and when doors can and cannot be accessed
- Manually override programming to lock or grant access
- Ease of Installation
-
- Self-contained unit, with single-wire connectivity reduces wire installation and cost
- Power-over-Ethernet (PoE) compatibility eliminates the need for separate power-supplies for door-locks and card readers
- Supports Uninterruptible Power Supply (UPS) for PoE, eliminating the need for individual equipment back-up batteries
- Wiring for readers, relays, and locks stays local at the door between the appliance and the A1001 controller
- Automatic discovery supported for Axis and compatible products
- After configuring, the system will generate a printable wiring diagram for the unit based on the equipment being installed
- Events and Alarms
-
- Tamper detection: An alarm is tripped when the unit cover is removed, if the unit is removed from mounting position, or if the reader is tampered with
- Power or network connection loss trips an event alarm
- Open-too-long alarm: When a door is wired with a contact, a programmable time period a door can be left open before an alarm is tripped
- When an event is detected, a signal is sent to the configurable external port for an alarm panel, NVR surveillance system, or other external device
- Automatic email notifications and event/alarm logs
- Single events can trigger multiple actions
- Locks
-
- Fail-secure or fail-open, and N/O or N/C options when wiring door locks
- Selectable to lock immediately after the door opens, or set to a delay
- Pre-alarm and pre-lock signal: A warning signal lets either the monitor and/or user know when the open-too-long alarm will trip, or when the door will lock
- Door unlock-time: The period of time the door will stay unlocked. Automatically locks when door closes after opening
- Readers
-
- Compatible with most reader and Wiegand protocols
- Supports Request-to-Exit (REX) devices like buttons, sensors, or push-bar. Selectable N/O or N/C
- Require-manual-unlock option
In the Box Axis Communications A1001 Network Door Controller 4 x Cable Ties Connector Kit Limited 3-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Axis Communications A1001 Network Door Controller in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersAxis Communications 0540-001 Specs | Input/Output Connections | 2 x Card reader data terminal block:RS485 full-duplexRS485 half-duplexWiegand
2 x Card reader I/O terminal block:2 x four configurable I/ODigital input: 0 to 40 VDC maxDigital output: 0 to 40 VDC maxOpen drain: 100 mA maximum
1 x Auxiliary terminal block:3.3 VDC output, 100 mA maximum2 x configurable I/ODigital input: 0 to 40 VDC maximumDigital output: 0 to 40 VDC maximumOpen drain: 100 mA maximum
2 x Door connector terminal block:For door monitors and Request to Exit (REX)Digital input: 0 to 40 VDC maximum | | Network Connection | 1 x RJ45 10/100 Ethernet port | | Network Protocols | IPv4, HTTP, HTTPS, SSL/TLS, QoS layer 3 DiffServ, FTP, SMTP, Bonjour, UPnP, SNMPv1/v2c/v3 (MIB-II), DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS | | Security Protocol | Password protection, IP address filtering, HTTPS encryption, IEEE 802.1X network access control, Digest authentication, User access log | | Memory | RAM: 256 MB
Flash 4 GB | | Power Input | Power-over-Ethernet IEEE 802.3af/802.3at Type 1 Class 3
10 - 30 VDC, 26 W maximum | | Power Output | Power-out and relay: 1 x 12 VDC, 500 mA maximum; 1 x solid-state relay 30 VDC, 700 mA maximum
Power-out lock: 2 x 12 VDC, 500 mA maximum | | Approvals | EN 55022 Class B, EN 50130-4, EN 61000-3-2, EN 61000-3-3, EN 55024, EN 61000-6-1, EN 61000-6-2, FCC Part 15 Subpart B Class B, ICES-003 Class B, C-tick AS/NZS CISPR22 Class B, VCCI Class B, IEC/EN/UL 60950-1, UL 294, UL 2043, EN 50581 | | Environmental | Operating temperature: 0 to 50°C (32 to 122°F)
Humidity: 20 to 85% non-condensing | | Dimensions | 7.1 x 7.1 x 1.8" (18.0 x 18.0 x 4.5 cm) | | Weight | 17.6 oz (500 g) | | | | Package Weight | 1.7 lb | | Box Dimensions (LxWxH) | 9.1 x 9.0 x 2.8" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 47 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
