|
User Manual for Bogen Communications BPA60 60W Power Amplifier Click to enlarge the picture
Contents of the user manual for the Bogen Communications BPA60 60W Power Amplifier
- Product category: Standard Amplifiers Bogen Communications
- Brand: Bogen Communications
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Bogen Communications Standard Amplifiers
|
User manual for the Bogen Communications BPA60 60W Power Amplifier contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Bogen Communications product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Bogen Communications user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Bogen Communications product will considerably shorten its lifespan!
|
Product description The BPA60 from Bogen is a solid-state, 60W power amplifier that has been designed for professional and commercial sound systems. It can be driven from an amplifier that provides a 25- or 70-volt output and is thermally protected to prevent damage due to excessive temperatures.Additional protection for the amp is provided by transient protection diodes and an electrical circuit breaker. The illuminated on/off power switch is located on the front panel. An input level control, circuit breaker reset, low-cut filter switch, and auxiliary receptacle are located on the rear panel. - Selectable outputs modes of 8-ohm/25V, 16-ohms, 25V CT, and 70V
- The BPA60 can operate at full output even with ambient temperatures up to 130°F
UPC: 765368350098 In the Box Bogen Communications BPA60 60W Power Amplifier Limited 1-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Bogen Communications BPA60 60W Power Amplifier in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersBogen Communications BPA60 Specs | Rated Power Output | 60 W | | THD (Main Outputs) | <2% from 50 Hz to 15 kHz | | Frequency Response | 20 Hz to 20 kHz (-2 dB) | | Input Sensitivity | High-Impedance: 300 mV
Low-Impedance Balanced, with Transformer (Available Separately): 75 mV | | Hum & Noise | 85 dB Below Rated Output | | Output Load | 8-Ohm/25 V, 16-Ohms, 25 VCT, 70 V | | Output Regulation | Better Than 2 dB from No Load to Full Load | | Input Impedance | High-Impedance, 50 kOhms Unbalanced; Low-Impedance, 600 Ohms, Balanced or Unbalanced; 1:1 Bridging with Accessory Transformer | | Low-Cut Filter | -10 dB at 100 Hz (Selectable) | | Controls and Indicators | Front Panel: Illuminated On/Off Power Switch,
Rear Panel: Input Level Control, Circuit Breaker Reset, Lo-Cut Filter Switch | | Power Consumption | 120 VAC, 60 Hz 180 W at Full Rated Output | | Thermal | Emissions (Full Power): 204.9 BTU/Hr. | | Overload Protection | Transient Protection Diodes, Electrical Circuit Breaker, Thermostat | | Connectors | Terminal Strip (Output)
RCA (Input)
Terminal Strip Balanced Lo-Z (Input) | | Operating Temperature Range | -4 to 131°F / -20 to 55°C at Rated Output | | Dimensions | 15.25 x 3.50 x 8.25" / 38.74 x 8.89 x 20.96 cm | | Weight | 17.0 lb / 7.7 kg | | | | Package Weight | 17.4 lb | | Box Dimensions (LxWxH) | 18.4 x 11.4 x 7.0" |
Rating80% users recommend this product to others. And what about you?
This product has already been rated by 27 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
inspiron 3470...
Film Scanner 8 mm + super 8 REELS MOVIE MAKER PRO...
HP 3630 deskjet printer/scanner...
Dell KB216 ITALIAN Slim Office Multimedia Keyboard BLACK.
...
Mistral MC2300R 25L Detachable Air Coller with Steriliser.
Thank you in advance for your assistance.
Sincerely,
Jonathan Chua...
|
| Discussion |
Latest contributions to the discussion:
Provident aut voluptas.
Name: Ophelia Crist
Logitech Wireless Presenter R400
this product is perplexed....
Feedback regarding your services
Name: Jessica Parisian
Logitech Wireless Presenter R400
I tried to cremate it but got Turkish Delight all over it....
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
|
|
