|
User Manual for Burst Electronics VS4x1 Four Input Active Switcher Click to enlarge the picture
Contents of the user manual for the Burst Electronics VS4x1 Four Input Active
- Product category: Routers & Switchers Burst Electronics
- Brand: Burst Electronics
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Burst Electronics Routers & Switchers
|
User manual for the Burst Electronics VS4x1 Four Input Active contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Burst Electronics product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Burst Electronics user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Burst Electronics product will considerably shorten its lifespan!
|
Product description The Burst Electronics VS4x1 4-input Active Switcher is a vertical interval video switcher with 4 inputs and 1 output and features digital logic to restrain selection of an idle input (no video). Jump-free switching between genlocked sources is achieved by DC-clamped inputs (back porch) and DC-clamped output. Besides allowing selection of only active (input video present) input channels, the 4-input Active Switcher can also be used when both audio and video are to be switched by using it as a slave with the AS4x1 audio switcher. In addition to offering audio follow video and breakaway switching, the switcher can also eliminate level shifts on the incoming video and ground reference the outgoing video. Featuring the BNC video connector, the VS4x1 4-input Active Switcher also has a 4-pin Mini DIN for Y/C option. The switcher also has an input for RS-232 remote control (2400 bps, 8N1), and an LED that shows the selected active channel. It uses an external 12VDC source and comes with a wall module power supply. - Vertical interval video switcher with 4 inputs and 1 output
- Features digital logic to restrain selection of an idle input (no video)
- Jump-free switching between genlocked sources is achieved by DC-clamped inputs (back porch) and DC-clamped output
- When used as a slave with the AS4x1 audio switcher, it can be used when both audio and video are to be switched
- Can eliminate level shifts on the incoming video and ground reference the outgoing video
- Allows selection of active (input video present) input channels
- Offers audio follow video and breakaway switching
- Includes BNC video connector and 4-pin Mini DIN for Y/C option
- Offers remote control via RS-232 (2400 bps, 8N1)
- LED for indicating the currently selected active channel
- Includes wall module power supply
In the Box Burst Electronics VS4x1 Four Input Active Switcher 12VDC Wall Adapter 1 Year Parts and Labor Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Burst Electronics VS4x1 Four Input Active Switcher in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersBurst Electronics VS4x1 Specs Input | 1V standard video | Output | 1V standard video | Video Bandwidth | 25MHz @ 1 dB | Differential Phase | 0.1° | Gain | Unity | Differential Gain | 0.1% | Video Signal-to-Noise Ratio | 60dB | Input Impedance | HiZ or 75 Ohms 1%, looping (jumper/switch selected) | Output Impedance | 75 Ohms 1% DC Clamped | Video Connector | BNC, 4-pin (Mini DIN - Y/C option) | Output Protection | Open or Short, infinite duration | Crosstalk | 60dB | Switching | Vertical Interval | Delay | Switching between channels: 200 ms | Power | 11-14VDC polarity insensitive | Power Source | 12VDC wall adapter (included): 120VAC 60Hz, 12VDC 500mAPolarity insensitive, the video switcher has an auto polarity feature. Do not use AC; use only DC. | Dimensions (WxDxH) | 4.1 x 5.5 x 1.5" (10.4 x 13.9 x 3.8cm) | | Package Weight | 3.0 lb | Box Dimensions (LxWxH) | 16.0 x 11.0 x 6.0" |
Rating80% users recommend this product to others. And what about you?
This product has already been rated by 47 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
looking for a user manual for Quickbooks Premier Nonprofit 2020 for a Disabled American Veterans office.... Bower SFD9260.... 4-IN-1 WIRELESS CHARGER
... Brand :Gemini,model # XGA 4000,AND IT WAS PURCHASED NEW IN 2022,OR POSSIBLY EARLY 2023.WORKED perfect till one day I hit power switch and blew fuse x2... ZZSTAR binoculars...
|
Discussion |
Latest contributions to the discussion:
v18 Name: Craig Mcinturff Davis & Sanford Provista 7518B Tripod I am looking for a camera mounting plate for a v18 fluid head Davis & Sandford ... Impact SF-ABRL160 Flash stopped working Name: Sarah sananes Impact SF-ABRL160 Stand Mount Flash with Hello, our flash is connected to a canon camera and all of the sudden the flash is no longer working.
Does the flash have a certain battery life? ... REPEAT REQUEST AS YOU DID NOT ANSWER YOU JUST SENT ME MY MESSAGE BACK -PLEASE HELP Name: Tish Hopkins Benro TAD37C Series 3 Adventure Carbon Hi again-- all this did was send this email back to me with a link that brought me right back here... what is this?? also a link to search for manuals-- ive been there done that there is NO Manual to be found that answers my ? Please HELP thanks!!
Hi there is an extra small sc... Tripod heads DO NOT sit flush on the plate of the tripod Help Please Name: Tish Hopkins Benro TAD37C Series 3 Adventure Carbon Hi there is an extra small screw on the plate that the tripod head screws on that prevents my gimbal tripod head from sitting flush when it is screwed on. this is very annoying and does not allow my camera to stay steady when shooting. Please tell me how to resolve this issue. th... battery replacement Name: Danette L Boyd-Perez Doxie Go SE Portable Scanner Hello-- I have been working w/ support- it seems they sent incorrect battery replacement.
I confirmed DX-255 and was sent battery NP 120. There is no way that battery fits inside the panel of the DX-255. Please advise next steps thank you....
|
|