|
User Manual for DJI Naza-M V2 Flight Controller with GPS Click to enlarge the picture
Contents of the user manual for the DJI Naza-M V2 Flight Controller with
- Product category: DJI Accessories DJI
- Brand: DJI
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for DJI DJI Accessories
|
User manual for the DJI Naza-M V2 Flight Controller with contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any DJI product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official DJI user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a DJI product will considerably shorten its lifespan!
|
Product description Supporting nine multi-rotor configurations, the Naza-M V2 Flight Controller with GPS from DJI acts as the brains of the aircraft, managing pilot input and interpreting data from the various sensors, helping maintain a stable flying condition. There are four components to the system. The MC (main controller) houses the flight computer and is at the heart of the flight control system. Then there is the PMU (power management unit), which serves to regulate how much power is sent to each of the four, six, or eight rotors. Next is an LED unit for status display, which features a micro-USB port for connecting the Naza-M V2 to a computer when configuring or testing using the Windows assistant software. Finally, a GPUs receiver/compass combo is included, which enables a number of features, including Intelligent Orientation Control (IOC) and the Go Home failsafe.
CAN-Bus ports on the MC allows the Naza-M to interface with a number of DJI accessories, including the Ground Station System, the iOSD Module, or a gimbal control unit (GCU). - Supports 9 Multi-rotor Configurations
- Quad I, Quad X, Hex I, Hex V, Hex Y, Hex IY, Oct X, Oct I, Oct V
- Supports DJI Ground Station
- By adding the separately available Bluetooth Datalink to the flight control system, you can plot waypoint-based autopilot courses using an iPad app or Windows software
- Software-Based Aircraft Stabilization
- The system works with or without GPS, and helps keep the aircraft stable and on course by taking data from gyros and other sensors and apply it to any pilot inputs. Naza-M V2 features GPS course correction plus GPS and compass interference monitoring, which combine to prevent the aircraft drifting off course do to magnetic interference that may throw off the compass (the GPS must be enabled and properly calibrated for this feature to work)
- Takeoff Assistance
- Helps ensure a stable, drift-free take off even on uneven surfaces
- Intelligent Orientation Control (IOC)
- Because multi-rotors are virtually symmetrical, it can be easy to lose track of which end is the "front". IOC features two modes to help make flying more intuitive:
- Core Lock: "Forward" is always the same as the direction the nose was pointing when the aircraft first took-off, regardless of the actual orientation of the aircraft
- Home Lock: "Forward" is always away from the origin defined by the Home Point that was established during GPS calibration. In other words, "forward" will be away from the Home Point (pilot) and "back" always toward the Home Point. Moving the stick right or left will cause the aircraft to follow a circular path around the Home Point
- Motor Failure Protection
- If a hexrotor or octorotor equipped with a Naza-M V2 suffers a single motor failure in flight while in attitude or GPS mode, it will maintain its altitude and rotate around the stopped motor. This allows it to fly safely back to home and land
Note: This feature does not work for quadcopters - Failsafe and Auto Go Home Support
- If the connection between the multi-rotor and the remote control (transmitter) are disconnected during flight, a failsafe system will activate. Provided there was enough GPS signal at the time of the disconnection, the multi-rotor will fly back to its point of takeoff and land automatically. This feature can also be triggered manually using the One-Key Go-Home function activated using Assistant software
- Assistant Software for Mobile Devices
- Using an iOS mobile device with Bluetooth LE support, parameters can be adjusted at any time the multi-rotor is within range. Connection records are automatically stored by the Bluetooth module and protected by password. Where Internet access is available, parameters can be automatically synchronized to the cloud and restored immediately if you switch to a different mobile device
- Built-in Functions
-
- Multiple autopilot control modes
- Enhanced fail-safe
- Low voltage protection
- S-Bus receiver support
- PPM receiver support
- Independent PMU module
- 2-axis gimbal support
In the Box DJI Naza-M V2 Flight Controller with GPS MC (Main Controller) PMU (Power Management Unit) GPS/Compass LED User Manual PDF 1.7mb Table of Contents
|
Upload User Manual
Have you got an user manual for the DJI Naza-M V2 Flight Controller with GPS in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersDJI CP.NZ.000011 Specs | Supported Multi-rotors | Quad-rotor: I4, X4
Hex-rotor: I6, X6, IY6, Y6
Octo-rotor I8, V8, X8 | | Supported ESC Output | 400 Hz refresh frequency | | Supported Transmitters | PCM or 2.4 GHz radio with at least 4 channels | | Working Range | MC: 4.8 to 5.5 V
VU Input: 7.4 to 26.0 V (2S to 6S LiPo recommended)
Output(V-SEN Port Red Wire): 3 A at 5 V (burst current: 7.5 A) | | Power Consumption | MAX: 1.5 W (0.3 A at 5 V)
Normal: 0.6 W (0.12 A at 5V) | | Operating Temperature | 14 to 122°:F / -10 to 50°C | | | | Assistant Software | Windows: 8, 7, XP SP3
OS X: 10.6 or later
Mobile: iPhone 4s, iPhone 5, iPod touch 5, iPad mini, iPad 4 | | | | Hovering Accuracy (GPS Mode) | Vertical: ±2.6' / ±0.8 m
Horizontal: ±8.2' / ±2.5 m | | Max Angular Speed | 200°/s | | Max Tilt Angle | 35° | | Ascent/Descent | Ascent: 19.7 ft/s / 6 m/s
Descent: 14.8 ft/s / 4.5 m/s | | | | Weight | MC: 1 oz / 27 g
PMU: 1 oz / 28 g
GPS: 1 oz / 27 g
LED: 0.5 oz / 13 g | | Dimensions | MC: 1.8 x 1.3 x 1.3" / 45.5 x 32.5 x 18.5 mm
PMU: 1.6 x 1.1 x 0.4" / 39.5 x 27.5 x 10 mm
GPS & Compass: 1.8 (diameter) x 0.4" / 46 (diameter) x 10 mm
LED: 1 x 1 x 0.3" / 25 x 25 x 7.0 mm | | | | Package Weight | 0.6 lb | | Box Dimensions (LxWxH) | 4.9 x 3.5 x 3.0" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 65 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
pocket quadcopter RIV-YT320...
CYBERPOWERPC GMA6200BSTV2...
FUJINON ERD-30A-D01A ZOOM DEMAND CONTROLLER
...
Just bought from Bestbuy Cyberpower,GMA5600BSTV4,model C series
another number on the label ET8252-10294
CECModel:CS450217MB492126 mfg date 043025
...
Vortex crossfire ii 6-24x50
I essentially want to return my scope to mechanical zero. This has been on a couple rifles and I would like to set f...
|
|
