|
User Manual for Earthworks M50 - Measurement Microphone Click to enlarge the picture
Contents of the user manual for the Earthworks M50 - Measurement Microphone
- Product category: Stereo & Specialty Microphones Earthworks
- Brand: Earthworks
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Earthworks Stereo & Specialty Microphones
|
User manual for the Earthworks M50 - Measurement Microphone contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Earthworks product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Earthworks user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Earthworks product will considerably shorten its lifespan!
|
Product description The Earthworks M50 is a professional measurement microphone intended for large room calibration. The ultra wide frequency response of 3Hz to 50kHz is flat throughout the entire spectrum and results in accurate room calibration using Smaart, MLSSA, SIMM and TEF based systems. The small element yields an omni-directional pattern resulting in a wide pick up area at the front and sides of the microphone capsule. The M50 also ships with a "white" noise generator that is capable of adapting to a 1/2" calibrator adapter for field calibration. - Matched Pair
- This stereo set of Earthworks M50 microphones are perfectly matched in sensitivity and frequency response from the manufacturer.
- Miniature Omni-directional Capsule
- The miniature element provides an accurate omni-directional pattern with an even coherent response at the direct and off-axis sections of the microphone capsule.
- Wide Linear Frequency Response
- The wide, linear frequency response accurately captures audio signal and reproduces the slightest nuance with great detail.
- Uncolored Response
- The uncolored, flat signal results in accurate room calibration for indoor and outdoor application.
UPC: 827517150550 In the Box Earthworks M50 - Measurement Microphone (Matched Pair) White Noise Calibrator Case 2 x Stand Clamp Limited 15-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Earthworks M50 - Measurement Microphone in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersEarthworks M50 Specs | Transducer | Condenser | | Polar Pattern | Omnidirectional | | Frequency Response | +/- 1dB 3Hz to 50kHz +1 / -3dB | | Dynamic Range (Typical) | 72dB | | Signal-to-Noise Ratio | 22dB SPL Equivalent (A weighted) | | Maximum Input Sound Level | 142dB SPL | | Power Requirements | +48V Phantom, 10mA | | Output Impedance | 600 ohms betweenpin 2 and pin 3 | | Output Connectors | XLR intended to drive a balanced transformerless input Pin2+ | | Pad | No | | Low Frequency Roll-Off | No | | Dimensions | 9 x .860" (229 x 22mm)(Length x Diameter) | | Weight | 225g (.5 lb) | | | | Package Weight | 3.3 lb | | Box Dimensions (LxWxH) | 12.5 x 6.5 x 3.0" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 34 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
call of duty world war II...
Audio Technica AUDIO-AT8631
data sheet ...
Sunpak Ultra 7000TM 2-1 tripod/monopod...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
