|
User Manual for Eden Amplification Module Terra Nova Bass Preamp Pedal Click to enlarge the picture
Contents of the user manual for the Eden Amplification Module Terra Nova Bass
- Product category: Effects Pedals Eden Amplification
- Brand: Eden Amplification
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Eden Amplification Effects Pedals
|
User manual for the Eden Amplification Module Terra Nova Bass contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Eden Amplification product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Eden Amplification user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Eden Amplification product will considerably shorten its lifespan!
|
Product description Designed primarily for electric bassists, the Eden Module is a preamp pedal based on Eden’s Terra Nova amplifiers. The pedal provides separate controls for input and output gain, as well as a switchable compressor for evening out your tone. An Enhance circuit provides a broad, one knob tone control for achieving your general sound, which you can then tweak further with the semi-parametric equalizer. Low and High knobs adjust your bass and treble ranges respectively, while two midrange knobs boast selectable frequency ranges to fine tune your timbre.The pedal sports active and passive inputs, stereo outputs, and an effects loop that you can bypass with a footswitch. To feed sound straight to a house PA or recording interface, an XLR DI output is offered. You can also mute the signal and instantiate the enhance circuit with dedicated footswitches. A power cable is included with the Module. - Controls at a Glance
- Mute Footswitch: Use this to mute or unmute the pedalEnhance Footswitch: This footswitch engages/disengages the Enhance featureLoop Footswitch: Use this to engage or bypass the external effects loopCompressor Switch: This turns the compressor circuit on and offInput Gain Knob: This adjusts the amount of signal sent into the preamp stageEnhance Knob: This circuit is an EQ sweep that simultaneously boosts extreme lows, upper mids, and highs while cutting lower midrange frequencies. This is a broad control that can help you achieve the overall right tone before moving on to the more granular EQBass Knob: This adjusts the low frequencies of the pedalBass Boost Switch: When engaged, the Bass control will offer a more pronounced adjustmentLow Mid Switch: This adjusts the low-midrange frequencies; use this in conjunction with the Low Mid Freq Sweep controlLow Mid Freq Sweep Knob: This adjusts the range of operation of the Low Mid switch, from 30 to 300 HzHi Mid Level Control: This knob adjusts the high-midrange frequencies; use it in conjunction with the Hi Mid Freq Sweep controlHi Mid Freq Sweep Knob: Use this control to adjust the range operation of the Hi Mid knob, from 200 to 2000 HzTreble Knob: This adjusts the highest frequencies of the spectrumMaster Knob: Use this knob to control the overall output level
- Connections
- Active Input: Use this 1/4" jack with active instrumentsPassive Input: Plug your low-output or passive instrument into this 1/4" jackStereo Outputs: The preamp has two 1/4" outputs, though you can of course run your instrument in monoAuxiliary Input: Connect an external device to the preamp using a 3.5mm cableHeadphone Output: Connect your headphones here using standard 3.5mm headphone cableSend/Return Jacks: Send your sound and receive its return signal from any outboard gear you’d like to use with the preampTuner Output: This output feeds clean signal to a dedicated tuner
In the Box Eden Amplification Module Terra Nova Bass Preamp Pedal Limited 1-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Eden Amplification Module Terra Nova Bass Preamp Pedal in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersEden Amplification Module Terra Nova Specs | Controls | Mute footswitch
Enhance footswitch
Loop footswitch
Compressor switch
Input gain knob
Enhance knob
Bass knob
Bass Boost switch
Low Mid switch
Low Mid freq sweep knob
Hi Mid level control
Hi Mid freq sweep knob
Treble knob
Master knob | | Connections | 2 x 1/4" instrument inputs, phone type
1 x 1/4" return input, phone type
1 x 3.5 mm auxiliary input jack
2 x 1/4" instrument output, phone type
1 x 1/4" send output, phone type
1 x 1/4" tuner output, phone type
1 x 3.5 mm headphone output
1 x XLR DI output | | Power Supply | 15 to 18 VDC power supply (included) | | Dimensions (H x W x D) | 2.8 x 10.2 x 6.3" / 7.0 x 26.0 x 16.0 cm | | Weight | 3.5 lb / 1.6 kg |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 85 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
I need a user manual and parts diagram for a Manfrotto Super Salon 280 Camera Stand - 9’
Thanks!...
OBIHI phone model number obi1032...
Instructions manual for a SONY woofer Model number: SA-W10...
I need the manual for a printer Brother MFC-J805DW. Reason is cause my printer is not recognizing the generic color cartridges LC3035...
I have a question, can you contact me at valenti-lanza@m.spheremail.net ? Cheers!...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Bruce Dunn
Avid Sibelius | Ultimate Standalone Perpetual
I seem to have lost the lower right hand icon that allows me to input notes, rests, voices etc. Can you tell me how to get it back?...
Difficult to remove the gooseneck mic. Help or advice needed.
Name: Joe Matos
Telex MCP90-18 - Panel Mount Gooseneck
Hi, I picked up an RTS KP-32 intercom and it has a gooseneck MCP90 mic installed, however I can't get it to come off. I read that it is reverse threaded 1/ 4" TRS, however when I tried by gripping it hard and turning clockwise, it still didn't come off. And turning counterc...
Question
Name: Dean Williams
Moultrie ATV Food Plot Spreader -
When spreading seed, does the gate automatically close when you turn the spreader off? Or do you have to close the gate via some other action?...
Video Promotion for your website?
Name: Joanna Riggs
Salamander Designs Keyboard Storage Shelf for
Hi,
I just visited search-manual.com and wondered if you'd ever thought about having an engaging video to explain or promote what you do?
Our prices start from just $195 USD.
Let me know if you're interested in seeing samples of our previous work.
Regards,
Joanna...
Need a REPAIR manual
Name: Dennis Behrends
Loctek Flexispot V9 Desk Exercise Bike
How do I get a REPAIR manual for a Loctek Flexispot V9 Desk Exercise Bike. I cannot get the petal crank off so I can remove the side panel. I have a crank removal tool but I'm afraid it will strip the threads because it is really stuck on there....
|
|
