|
User Manual for FSR 1x2 Computer Distribution Amplifiers Click to enlarge the picture
Contents of the user manual for the FSR 1x2 Computer Distribution Amplifiers
- Product category: Distribution Amplifiers (DA's) FSR
- Brand: FSR
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for FSR Distribution Amplifiers (DA's)
|
User manual for the FSR 1x2 Computer Distribution Amplifiers contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any FSR product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official FSR user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a FSR product will considerably shorten its lifespan!
|
Product description This 50 pack of 1x2 Computer Distribution Amplifiers from FSR lets you distribute a computer's VGA video signal simultaneously to a VGA monitor and projector or LCD panel. Featuring a 300MHz bandwidth, it supports resolutions up to QXGA (2048 x 1536 @ 60Hz), and it buffers each output individually to maintain signal integrity. ID bits are communicated through the monitor output to allow your monitor to determine the video resolution of your signal.
The maximum cable length supported is approximately 50 ft (cable dependent) on input and output. 50 units are included in this bundle, each with a 5 ft VGA cable, locking power supply, and rubber mounting feet. The enclosure is made of durable metal and the rubber feet will allow you to avoid any damage to furniture in desktop use. - Key Features
-
- Distributes VGA signal to a monitor and projector/LCD panel
- Buffers each output individually
- 300MHz bandwidth supporting resolutions up to QXGA (2048 x 1536 @ 60Hz)
- ID bits are communicated through the monitor output
- Supports approximately 50 ft cable lengths
- Includes 5 ft VGA cables, locking power supplies, and rubber mounting feet
- Metal enclosure
In the Box FSR 1x2 Computer Distribution Amplifiers (50 Pack) 50 x Locking Power Supplies 50 x 5 ft (1.5 m) VGA Male to Male Cables 50 x Sets of Rubber Mounting Feet 60-Day Limited Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the FSR 1x2 Computer Distribution Amplifiers in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersFSR CDA-2-50 Specs | Input | 1x VGA 15-pin HD female (RGB + Sync) | | Input Level | Nominal: Analog 0.7 V p-p; Maximum: 2 V p-p | | Input Impedance | 75 ohms | | Horizontal Frequency | 15 - 200 kHz | | Vertical Frequency | 30 - 150 Hz | | Output | 2x VGA 15-pin HD female (RGB + Sync) | | Output Level | Nominal: Unity | | Output Impedance | 75 ohms | | Sync Input & Output | Sync On Green, Composite Sync, Separate Sync (same as input) | | Sync Input Level | 2 - 5 V | | Sync Output Level | 2.4 V into 75 ohms | | Sync Input Impedance | 4.8 V into Hi-Z | | Sync Output Impedance | 75 ohms | | Sync Propagation Delay (max) | Typical 5 nS | | Sync Rise / Fall Time | 2.5 nS | | Sync Polarity | Matched to input polarity | | Bandwidth | >300 MHz | | Supported Resolution | Up to QXGA (2048 x 1536 @ 60 Hz) | | Supported Cable Length | Approximately 50 ft (15 m), cable dependent | | Power Requirements | 12 V DC @ 125 mA | | Enclosure | Metal | | Dimensions | 3.6 x 2.6 x 1" (9 x 6.6 x 2.5 cm) | | Weight | 14 oz (0.4 kg) |
Rating50% users recommend this product to others. And what about you?
This product has already been rated by 30 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
ESENIOR CG4-141-3CCT-BL-ZY
14" LED Light Bar...
Cannon Pixma TS202 ...
POSS PSHS60 CD Player in English...
Romeo 5 red dot ...
ImageBox 9MP Standalone film & photo convertor...
|
| Discussion |
Latest contributions to the discussion:
How do I disassemble the ends to trim the length of the product (THE VANGUARD MULTI-MOUNT6) ?
Name: GUILLERMO HERNANDEZ
Vanguard Multi-Mount 6 Tripod Utility Bar
How do I disassemble the ends to trim the length of the product (THE VANGUARD MULTI-MOUNT6) ?...
logitech extreme 3D pro
Name: Al Wahba
Logitech Extreme 3D Pro Joystick
I want to activate the set with game flight simulator standard 2020 to contol the plane instrument...
Cokin "A" Series Filter to "P" Series Holder Adapter
Name: Mike Compton
Cokin "A" Series Filter to "P"
Hello, By chance, would you know where I can purchase a Cokin "A" Series Filter to "P" Series Holder Adapter? Thank you....
suction cup for windshield
Name: Dave Seroka
Papago GoSafe 30G Dash Camera with
I am looking for a replacement suction cup for the windshield for my PapaGo safe 30G dash cam The one I have will not stick to the windshield. Could you send me information on where to get one...
TR-P5TP pink robot dog
Name: Allyson
Top Race Race & Remote Control
Hello we are having issues with the remote to the robot dog it just flashes a red light will not sync to the robot dog what so ever the dog is charged and batteries have been changed out more the once, Can i get help trouble shooting the issue or if something needs to be sent bac...
|
|
