|
User Manual for Henry Engineering DigiMatch 2x6 - AES EBU S PDIF Interface and Distribution Amplifier Click to enlarge the picture
Contents of the user manual for the Henry Engineering DigiMatch 2x6 - AES
- Product category: Format Converters Henry Engineering
- Brand: Henry Engineering
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Henry Engineering Format Converters
|
User manual for the Henry Engineering DigiMatch 2x6 - AES contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Henry Engineering product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Henry Engineering user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Henry Engineering product will considerably shorten its lifespan!
|
Product description The DigiMatch 2x6 from Henry Engineering is an AES/EBU to S/PDIF interface and distribution amplifier designed for the purposes of converting between the two types of digital audio signals and distributing them to multiple outputs. It features single AES/EBU and S/PDIF inputs and three outputs for each format. Either input can feed all six of the outputs, creating four modes of operation, which are selected via the front panel.
In "convert" mode the AES/EBU input feeds the S/PDIF outputs while the S/PDIF input feed the AES/EBU outputs. In "DA-AES/EBU Only" mode the AES/EBU input feeds all of the outputs. "DA-S/PDIF Only" mode has the S/PDIF input feeding all six outputs. The "DA-Split" mode has each format's input being output through its own corresponding connectors.
Built-in DigiMatch circuitry corrects input levels that are out of tolerance. The AES/EBU connectors are transformer isolated and all of the outputs are short-circuit protected and can drive long cable lines without degrading the signal. All of these features packed into a 1/3 rack space unit make the DigiMatch a great choice for your digital audio conversion and distribution needs. - AES/EBU and S/PDIF converter and distributor
- Four operating modes to meet any situation
- Single AES/EBU and S/PDIF inputs, each with three outputs
- Internal signal tolerance correction circuitry
- Transformer-isolated AES/EBU connectors
- Short-circuit protection on all outputs
UPC: 837654309063 In the Box Henry Engineering DigiMatch 2x6 - AES/EBU/S/PDIF Interface and Distribution Amplifier 1 Year Limited Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Henry Engineering DigiMatch 2x6 - AES EBU S PDIF Interface and Distribution Amplifier in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersHenry Engineering DigiMatch 2x6 Specs | Sample Rate | Any, Up to 96kHz | | Inputs | AES/EBU: XLR Connector, 110 ohm Termination (Switchable)
S/PDIF: RCA Connector, 75 ohm Termination (Switchable) | | Outputs | AES/EBU: 3 x XLR Connectors, 110 ohm Source Impedance
S/PDIF: 3 x RCA Connectors, 75 ohm Source Impedance | | Throughput Delay | Less than 80 Nanoseconds | | Power Input | 115/230VAC, 5W | | Dimensions (WxHxD) | 5.7 x 1.75 x 6" (145 x 44 x 152mm) | | Weight | 3 lbs (1.4 kg) | | | | Package Weight | 2.28 lb | | Box Dimensions (LxWxH) | 8.5 x 6.4 x 1.5" |
Rating90% users recommend this product to others. And what about you?
This product has already been rated by 73 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
ESENIOR CG4-141-3CCT-BL-ZY
14" LED Light Bar...
Cannon Pixma TS202 ...
POSS PSHS60 CD Player in English...
Romeo 5 red dot ...
ImageBox 9MP Standalone film & photo convertor...
|
| Discussion |
Latest contributions to the discussion:
How do I disassemble the ends to trim the length of the product (THE VANGUARD MULTI-MOUNT6) ?
Name: GUILLERMO HERNANDEZ
Vanguard Multi-Mount 6 Tripod Utility Bar
How do I disassemble the ends to trim the length of the product (THE VANGUARD MULTI-MOUNT6) ?...
logitech extreme 3D pro
Name: Al Wahba
Logitech Extreme 3D Pro Joystick
I want to activate the set with game flight simulator standard 2020 to contol the plane instrument...
Cokin "A" Series Filter to "P" Series Holder Adapter
Name: Mike Compton
Cokin "A" Series Filter to "P"
Hello, By chance, would you know where I can purchase a Cokin "A" Series Filter to "P" Series Holder Adapter? Thank you....
suction cup for windshield
Name: Dave Seroka
Papago GoSafe 30G Dash Camera with
I am looking for a replacement suction cup for the windshield for my PapaGo safe 30G dash cam The one I have will not stick to the windshield. Could you send me information on where to get one...
TR-P5TP pink robot dog
Name: Allyson
Top Race Race & Remote Control
Hello we are having issues with the remote to the robot dog it just flashes a red light will not sync to the robot dog what so ever the dog is charged and batteries have been changed out more the once, Can i get help trouble shooting the issue or if something needs to be sent bac...
|
|
