|
User Manual for Joemeek oneQ2 Master Studio Channel Click to enlarge the picture
Contents of the user manual for the Joemeek oneQ2 Master Studio Channel
- Product category: Channel Strips Joemeek
- Brand: Joemeek
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Joemeek Channel Strips
|
User manual for the Joemeek oneQ2 Master Studio Channel contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Joemeek product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Joemeek user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Joemeek product will considerably shorten its lifespan!
|
Product description The Joemeek oneQ2 Master Studio Channel is a mic preamp and channel strip that contains a suite of professional studio tools in a single, 2U chasis. An updated version of the orignal oneQ, it offers improved audio specifications, routing options, and metering.
Front- and rear-panel XLR mic inputs make session setup easy. Other input options include a front-panel instrument input, and a rear-panel line input. The transformer-coupled preamp is equipped with a high-end Cinemag transformer. Adjust the amount of amplification with the Preamp Gain control, and eliminate rumble, pops, and handling noise with a switchable high-pass filter. By activating the IRON switch, you can route line input through the transformer
The oneQ2 sports an optical compressor that includes Compress (threshold), Slope (ratio), Attack, Release, and Makeup Gain controls. The Comp Link button and it corresponding rear-panel jack make it possible to link up a second oneQ2 when recording stereo sources.
The 4-band "Meequalizer" EQ can be switched in or out of the signal chain. The low-frequency and high frequency are each switchable between two center frequencies, and the low-mid and high-mid bands have sweepable frequency ranges. The front-panel Post EQ switch moves the compressor from before the EQ in the signal chain to after.
The Enhancer section is designed to add clarity but not extra gain to the input signal. Controls include Effect, which sets amount of the Enhancer; Range, for setting the frequency above which the effect is applied; and Q, which adds a resonant peak at the Range frequency.
Turn on the De-Esser effect to reduce sibalence in vocals. It lets you adjust the gain-reduction frequency; listen to the output of the sidechain filter, and adjust the threshold above which reduction is applied. A large and accurate VU meter can be set to display output level, preamp level, or gain reduction.
The oneQ2's outputs include XLR and 1/4" analog line outs, as well as AES/EBU, S/PDIF, and optical digital outputs. Wordclock input and output jacks on BNC connectors allow for synchronization with external clock sources or devices. - Ultra-clean microphone preamps, designed for high-quality, low-noise performance, and equipped with high-end Cinemag transformers
- Highly musical 4-Band EQ includes sweepable low-mid and high-mid frequencies, and selectable low and high frequencies (80 or 120 Hz, and 6 and 12kHz, respectively)
- Full-featured optical compressor with Comp Link for stereo applications
- De-Esser with Listen function for quick, precise elimination of sibilance
- Large, accurate VU meter; switchable between output level, preamp level, and gain reduction
- IRON switch routes the line input through the transformer.
- Front-panel instrument input to use as a DI during sessions
- XLR inputs on the front and rear panels for easy session setup
- Harmonic Enhancer adds definition without increasing gain
- 24-Bit/96 kHz analog-to-digital converters with AES/EBU, S/PDIF, optical, and Wordclock
- Channel 2 Analog Input allows an external balanced analog audio signal to be fed to (the otherwise unused) digital channel 2.
UPC: 850207000743 In the Box Joemeek oneQ2 Master Studio Channel Manual AC Power Cable Three (3) Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Joemeek oneQ2 Master Studio Channel in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersJoemeek oneQ2 Specs | | | Number of Channels | Single | | Inputs | 2 x XLR Microphone (transformer balanced)
1 x 1/4" TRS Line(balanced)
1 x 1/4" TS Instrument(balanced)
1 x 1/4" TRS Channel 2 Analog Input(balanced) | | Input Impedances | Mic: 1.2kΩ
Line: 20kΩ | | Preamp Overall Gain | -10 to 60 dB | | Common Mode Rejection | 70 dB | | Equivalent Input Noise | -128.5 dBu (unweighted) | | Frequency Response | 15 Hz to 70 kHz (-3 dB) | | Maximum Input Before Clipping | +21 dBu; Line: +45 dBu | | Distortion | 0.001% (below Compressor threshold) | | Headroom Before Clipping | +21 dBu | | Pad | 20 dB attenuation | | High-Pass Filter | 12 dB per octave cut below 80 Hz | | Phantom Power | 48 V (switchable) | | Analog Outputs | 1 x XLR (balanced)
1 x 1/4" TRS (balanced, switchable between +4 dBu and -10 dBv) Nominal Output Levels +4 dBu/-10 dBv | | Nominal Output Levels | +4 dBu/-10 dBv | | Output Impedance | Output Impedance: 75Ω | | Output Level Switch | 12 dB attenuation | | Noise Floor | -85 dBu (typical, with -40 dB mic gain) | | VU Meter | Analog movement | | Insert | 1 x 1/4" TRS Send and Return | | | | Threshold Range | -6 dBu to +22 dBu (variable) | | Ratio | 1:1 to 10:1 (variable) | | Attack Time | 1 to 100 ms (adaptive) | | Release Time | 0.1 to 3 sec (adaptive) | | | | Range (Boost/Cut) | ±15 dB on all bands (bell response) | | Frequency Bands | Low Frequency: 80/120 Hz (switchable)
Low-Mid Frequency: 200 Hz to 2 kHz (variable)
High-Mid Frequency: 1 to 6 kHz (variable)
High Frequency: 7/14 kHz(switchable) | | Q | 0.9 (1.6 octaves) | | | | Sampling | 24-bit | | Resolution | 24-bit delta sigma using Wolfson WM8738 ADC | | Sampling Rate | 44.1, 48, 88.2, or 96 kHz (selectable) | | Output Formats | AES3 compliant (balanced), S/PDIF electrical | | Oversampling | 2.4 x sample frequency | | Noise Floor | Typically 92 dB A-weighted (referenced to 0 dBFS = +18 dBu). For a +4 dBu signal, the SNR is 78 dB | | Distortion | Typically 0.01% @ 0 dBu (20 Hz - 20 kHz) at 96 kHz sample rate Typically 0.02% @ 0 dBu (20 Hz - 20 kHz) at 48 kHz sample rate Typically 0.02% @ -1 dBFS (2 0Hz - 20 kHz) at all sample rates | | External Wordclock Input | 75Ω, 1.25 V - TTL level, 44.1 kHz to 96 kHz (auto synchronising) | | Wordclock I/O | 1 x BNC Input 1 x BNC Output | | Crosstalk | Typically -67 dB (20 Hz - 20 kHz) | | | | Power Supply | 115V/230V AC mains, 50/60 Hz | | Power Consumption | 30 W | | | | Dimensions (WxDxH) | 19 x 8.7 x 3.5" (482 x 220 x 88 mm) | | Weight | 6.6 lb (3 kg) | | | | Package Weight | 10.8 lb | | Box Dimensions (LxWxH) | 24.2 x 10.8 x 5.3" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 77 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
call of duty world war II...
Audio Technica AUDIO-AT8631
data sheet ...
Sunpak Ultra 7000TM 2-1 tripod/monopod...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
