|
User Manual for Joemeek twinQ2 - Dual Studio Channel Click to enlarge the picture
Contents of the user manual for the Joemeek twinQ2 - Dual Studio Channel
- Product category: Channel Strips Joemeek
- Brand: Joemeek
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Joemeek Channel Strips
|
User manual for the Joemeek twinQ2 - Dual Studio Channel contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Joemeek product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Joemeek user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Joemeek product will considerably shorten its lifespan!
|
Product description The Joemeek twinQ2 is a dual-mono preamp and channel strip that's equipped with a comprehensive set of useful features. An updated version of the original twinQ, it improves on its predecessor by providing increased headroom and level, and more flexible routing of line-level signals.
Joemeek designed the preamp section for low noise and sonic purity. For each channel you get an XLR mic input, a 1/4" balanced line input, and a front-panel 1/4" high-impedance instrument input. The mic inputs are routed through high-quality Cinemag transformers, which provide pleasing sonic coloration. By activating the IRON switch, you can route line-level sources through the transformers. A Preamp Gain control is provided for adjusting the amount of amplification. A switchable high-pass filter helps eliminate rumble, pops, and handling noise.
A 3-band "Meequalizer" EQ is available on each channel, offering sweepable low and mid bands, and a high band with a selectable center frequency of 6 or 12 kHz. Each channel is also equipped with a full-featured optical compressor that includes Compress (threshold), Slope (ratio), Attack, Release, and Makeup Gain controls. Activating the Comp Link button couples the two channel's Compress, Attack, and Release controls, which helps prevent image shifts when inputting stereo signals. Large and accurate VU meters can be set to display output level, preamp level, or gain reduction.
The twinQ2 offers a range of output options: Each channel has XLR and 1/4" analog outputs, as well as AES/EBU, S/PDIF, and optical digital outputs. A Wordclock input on a BNC connector allows synchronization with an external clock source. - Ultra-clean microphone preamps, designed for high-quality, low-noise performance, and equipped with high-end Cinemag transformers
- IRON switch selects transformer coupling of the Line inputs.
- Full-featured optical compressor with Comp Link for stereo applications
- Large, accurate VU meters; switchable between output level, preamp level, and gain reduction
- 24-Bit/96 kHz analog-to-digital converters feed the AES/EBU, S/PDIF, and Optical digital outputs, allowing connection with external digital gear
- Balanced and unbalanced I/O allow for proper connection with any system
- Front-panel instrument inputs let you plug in high-impedance sources like guitars and basses
- Highly musical 3-Band EQ includes sweepable low and mid frequencies, and selectable high frequencies (6 and 12kHz)
UPC: 850207000842 In the Box Joemeek twinQ2 - Dual Studio Channel Manual AC Power Cable Three (3) Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Joemeek twinQ2 - Dual Studio Channel in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersJoemeek twinQ2 Specs | | | Number of Channels | 2 | | Inputs | 2 x XLR Microphone (transformer balanced)
2 x 1/4" TRS Line(balanced) 2 x 1/4" TS Instrument (balanced) | | Input Impedances | Mic: 1.2kΩ
Line: 10kΩ
Instrument: 2.2MΩ | | Preamp Overall Gain | -2 to 60 dB | | Equivalent Input Noise | -128.5 dBu (unweighted) | | Distortion | 0.001% (below Compressor threshold) | | Frequency Response | 10 Hz to 70 kHz (-3 dB) | | Maximum Input Before Clipping | Mic: +24 dBu; Line: +45 dBu | | Headroom Before Clipping | +29 dBu | | Common Mode Rejection | 70 dB | | Pad | 20 dB attenuation | | High-Pass Filter | 12 dB per octave cut below 80 Hz | | Phantom Power | 48 V (switchable per channel) | | Analog Outputs | 2 x XLR (balanced)
2 x 1/4" TRS (balanced) Nominal Output Levels +4 dBu/-10 dBv | | Nominal Output Levels | +4 dBu/-10 dBv | | Output Impedance | Output Impedance: 75Ω | | Output Level Switch | 12 dB attenuation | | Noise Floor | -85 dBu (typical, with -40 dB mic gain) | | VU Meter | Analog movement | | | | Threshold Range | -6 dBu to +22 dBu (variable) | | Ratio | 1:1 to 10:1 (variable) | | Attack Time | 1 to 100 ms (adaptive) | | Release Time | 0.1 to 3 sec (adaptive) | | | | Q | 0.9 (1.6 octaves) | | Range (Boost/Cut) | ±15 dB on all bands (bell response) | | Frequency Bands | Low Frequency: 40 to 650 Hz (variable)
Mid Frequency: 300 Hz to 5 kHz (variable)
High Frequency: 6/12 kHz (switchable) | | | | Sampling | 24-bit | | Resolution | 24-bit delta sigma using Wolfson WM8738 ADC | | Sampling Rate | 44.1, 48, 88.2, or 96 kHz (selectable) | | Output Formats | AES3 compliant (balanced), S/PDIF electrical | | Oversampling | 2.4 x sample frequency | | Noise Floor | Typically 92 dB A-weighted (referenced to 0 dBFS = +18 dBu). For a +4 dBu signal, the SNR is 78 dB | | Distortion | 0.01% @ 0 dBu at 96 kHz sample rate
0.02% @ 0 dBu at 48 kHz sample rate
0.02% @ -1 dBFS at all sample rates | | External Wordclock Input | 1 x BNC; 75Ω, 1.25 V - TTL level, 44.1 kHz to 96 kHz (auto synchronizing) | | Crosstalk | Typically -67 dB (20 Hz - 20 kHz) | | | | Power Supply | 115V/230V AC mains, 50/60 Hz | | Power Consumption | 30 W | | | | Dimensions (WxDxH) | 19 x 8.7 x 3.5" (482 x 220 x 88) | | Weight | 6.6 lb (3 kg) | | | | Package Weight | 13.65 lb | | Box Dimensions (LxWxH) | 24.0 x 10.8 x 5.0" |
Rating70% users recommend this product to others. And what about you?
This product has already been rated by 18 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Swan Bread maker SWBBA7...
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
call of duty world war II...
Audio Technica AUDIO-AT8631
data sheet ...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
