|
User Manual for JVC Multidyne FS-900 3-in-1 Fiber System for JVC GY-HM890 Click to enlarge the picture
Contents of the user manual for the JVC Multidyne FS-900 3-in-1 Fiber System
- Product category: Studio Systems JVC
- Brand: JVC
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for JVC Studio Systems
|
User manual for the JVC Multidyne FS-900 3-in-1 Fiber System contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any JVC product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official JVC user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a JVC product will considerably shorten its lifespan!
|
Product description The Multidyne FS-900 Fiber System from JVC offers bi-directional 3G-SDI 1080p/60 video feed-and-return for up to three JVC GY-HM890 camcorders using Neutrik opticalCON fiber cable and a single base station. Control, audio, sync, and intercom are also transmitted between camera and base station. The FS-900 base station has built-in gigabit Ethernet that works with the GY-HM890's streaming capabilities to provide video-over-IP transmission as well. Three camera adapters and one base are included in the system (cameras are available separately). The FS-900 base station is designed to integrate with existing systems, providing two HD/SDI outputs with return SDI and VBS connections (for analog signals), audio (RTS TW intercom module) and sync/control functions including bi-level /tri-level sync, teleprompter input, time code, GPI signals, and remote camera control input. The camera modules attach directly to the camera backs using a 68-pin interface, eliminating the need for external cable connectors. The base's redundant power supply offers a maximum of 150W for each camera and its accessories. - Camera Compatibility
- Designed to work with up to three JVC GY-HM890 ProHD camcorders and Neutrik opticalCON fiber optic cable
Key Features - Supports up to 1080p/60 video feed and returns
- The camera adapter is designed to use either JVC VF-HP790 or generic SDI monitors as viewfinders
- Provides both HDMI and SDI feeds for high-quality HD teleprompters
- Video-over-IP and web-based camera remote control using gigabit Ethernet
- Dual redundant power supplies
In the Box JVC Multidyne FS-900 3-in-1 Fiber System for JVC GY-HM890 (opticalCON) 3 x Camera Fiber Adapter Units Base Unit Limited 2-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the JVC Multidyne FS-900 3-in-1 Fiber System for JVC GY-HM890 in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersJVC FS-900BS1NCAM3 Specs | | | Fiber Cable Supported | Neutrik opticalCON | | | | Video Interface | SDI (SMPTE ST259)
HD-SDI (SMPTE ST292)
3G-SDI (SMPTE ST424) | | Data Rate | Data Rate: 270 Mbps, 1.5 Gbps, 3 Gbps | | Input/Output Level and Impedance | 800 mVpp, 75 Ohms | | | | Video Interface | SDI (SMPTE ST259)
HD-SDI (SMPTE ST292)
3G-SDI (SMPTE ST424)
HDMI (on return channel #3 only, for teleprompter use) | | Data Rate | Data Rate: 270 Mbps, 1.5 Gbps, 3 Gbps | | Input/Output Level and Impedance | 800 mVpp, 75 Ohms | | Connectors | 4 x BNC, 1 x HDMI (return channel # 3) | | Genlock Video Input | Number of Inputs: 1, plus loop output
Type: Analog black-burst, tri-level
Impedance: 75 Ohms
Camera Adapter: Internal
Base Unit Connector: 2 x BNC | | | | Type | Camera to Base: Embedded SDI
Base to Camera: Balanced analog line-level, mono | | Number of Channels | Camera to Base: Maximum supported by camera
Base to Camera: 2 | | Level | Base to Camera: +4 dBu nominal, +24 dBu maximum | | Connector | Camera Unit: DB9
Base Unit: DB25 | | Intercom | Number of Channels: 2
Interface: 2-wire or 4-wire
Compatibility: Clear-com
Camera Unit Connector: XLR-5
Headset Microphone Type: Dynamic
Microphone Impedance: 200 Ohms nominal
Base Unit Connector: DB25 | | Remote Control | Number of Channels: 1 per camera
Camera Unit Connector: Internal
Base Unit: 3 x 6-pin mini-DIN | | Ethernet | Number of Channels: 1 per camera
Data Rate: 10/100/1000 Base-T
Camera Unit Connector: RJ45 Cat5e
Base Unit Connectors: 3 x RJ45 Cat5e | | Timecode | Number, Base to Camera: 1 per camera
Number, Camera to Base: 1, from camera # 1 only
Inputs: Unbalanced, 15 Vpp max
Outputs: Unbalanced, 3 Vpp
Camera Unit Connector: Internal
Base Unit: BNC | | Tally / GPIO | Number, Base to Camera: 3 per camera (red, green, spare)
Number, Camera to Base: 1 per camera
Inputs: Short to GND or TTL low to activate
Outputs: Relay contact closure (30 V, 2 A max)
Camera Unit Connector: DB15 Base Unit Connector: DB25 | | Operating Wavelength | Operating Wavelength: 1471-1611 nm
Transmitter Laser Output Power: 0 dBm (class 1 laser)
Receiver Sensitivity: -20 dBm
Fiber Compatibility: Single-mode
Optical Connector Types: opticalCON DUO, SMPTE 304M | | | | Operating Temperature & Humidity | Operating Temperature & Humidity:
32-122°F (0-50°C)
0-95% relative humidity
Remote Power: Hybrid fiber connector
Battery Mount | | Power Input | Base Unit: 9-250 VAC, 50-60 Hz, IEC320, universal input
Camera: Remote power
Hybrid Fiber Connector: Local power
Battery Mount: Anton Bauer or optional V-mount | | Dimensions (HxWxD) | Camera Adapter: 8.2 x 6.7 x 4.2" (20.8 x 17 x 10.7 cm)
Base Unit: 3.5 x 19 x 16" (8.9 x 48.3 x 40.6 cm) (2 RU) |
Rating60% users recommend this product to others. And what about you?
This product has already been rated by 89 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Kingwin Super Speed 3.0 S/N KW11805020007...
Logitech MK850 Manual...
Swan Bread maker SWBBA7...
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
