|
User Manual for MASELEC MPL-2 Stereo Peak and High-Frequency Limiter Click to enlarge the picture
Contents of the user manual for the MASELEC MPL-2 Stereo Peak and High-Frequency
- Product category: Dynamics Processors MASELEC
- Brand: MASELEC
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for MASELEC Dynamics Processors
|
User manual for the MASELEC MPL-2 Stereo Peak and High-Frequency contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any MASELEC product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official MASELEC user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a MASELEC product will considerably shorten its lifespan!
|
Product description The MASELEC MPL-2 is a stereo peak and high-frequency limiter offering distortion-free peak limiting, smooth de-essing, and higher perceived loudness for producers and recording/mixing/mastering engineers in a variety of studio facilities. It features two distinct circuits—a wideband limiter and a high-frequency limiter—with independent threshold controls, on/off switches, and 6-segment LED gain reduction meters. The durable alloy enclosure occupies just 1 RU of rack space while providing stereo I/O via balanced XLR connectors, and simple, consolidated controls. Use the input gain to optimize your gain stage, then tweak each circuit's threshold to determine the amount of gain reduction applied by the peak limiter and high-frequency limiter. Engage the hard-knee mode to operate the peak limiter with a harder compression knee, decreased release time, and heightened loudness. The high-frequency limiter's mid-side sidechain mode allows increased de-essing on center-panned signals by lowering the sidechain threshold for the "mid" (center) signal. - Prevent peak levels from exceeding a designated limit
- Increases subjective loudness of stereo program material
- Gives digitally recorded content a more analog character
- Introduces a soft leveling function for large differences in average program levels
- Reduces dynamic range to maximize the performance of AD converters
- Adds no audible pumping resulting from limiting
In the Box MASELEC MPL-2 Stereo Peak and High-Frequency Limiter Power Cable Limited 1-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the MASELEC MPL-2 Stereo Peak and High-Frequency Limiter in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersMASELEC MPL-2 Specs | Function | Limiter / HF Limiter | | Number of Channels | 2 | | Inputs | 2 x 3-Pin XLR Female (Balanced) | | Outputs | 2 x 3-Pin XLR Male (Balanced) | | Input Impedance | 100 kOhms | | Output Impedance | 33 Ohms | | Maximum Input Level | +29 dBu | | Maximum Output Level | +29 dBu | | Compression Threshold | Limiter: +14 to +22 dBu
HF Limiter: 0 to 26 dB Below Limiter Threshold | | Compression Ratio | Not Specified by Manufacturer | | Attack Time | Limiter: Instant
HF Limiter: 1 to 20 ms (Program Dependent) | | Release Time | Program Dependent | | Make-up Gain | 0 to 10 dB | | Frequency Control | HF Limiter: > 2 kHz | | Frequency Response | Not Specified by Manufacturer | | Dynamic Range | Input: > 120 dB
Output: 100 to 120 dB | | Distortion | < 0.003% (Typical) | | Power Requirements | 90 to 130 VAC at 60 Hz, or 180 to 260 VAC at 50 Hz | | Fuse | 315 mA, Anti-Surge (Slow) | | Enclosure Material | Alloy | | Dimensions (W x H x D) | 19.0 x 1.8 x 10.2" / 48.3 x 4.4 x 25.9 cm | | Weight | 6.6 lb / 3 kg |
Rating70% users recommend this product to others. And what about you?
This product has already been rated by 21 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
inspiron 3470...
Film Scanner 8 mm + super 8 REELS MOVIE MAKER PRO...
HP 3630 deskjet printer/scanner...
Dell KB216 ITALIAN Slim Office Multimedia Keyboard BLACK.
...
Mistral MC2300R 25L Detachable Air Coller with Steriliser.
Thank you in advance for your assistance.
Sincerely,
Jonathan Chua...
|
| Discussion |
Latest contributions to the discussion:
Hello from Murray - Gutkowski
Name: Enos Greenholt
Logitech Wireless Presenter R400
I tried to pepper it but got prune all over it....
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
Help needed
Name: Ann Carter
SanDisk 1TB Extreme Portable USB 3.1
When I click the link to download the user manual for my Sandisk Extreme external hard drive, it gives me the manual for the LG Cricket. Can you please change the link so I can download the Sandisk manual and begin using this drive? Thank you....
|
|
