|
User Manual for Pelco USRACK 4RU Fiber Rack Mount With Internal Power Supply Click to enlarge the picture
Contents of the user manual for the Pelco USRACK 4RU Fiber Rack Mount
- Product category: Signal Extenders Pelco
- Brand: Pelco
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Pelco Signal Extenders
|
User manual for the Pelco USRACK 4RU Fiber Rack Mount contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Pelco product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Pelco user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Pelco product will considerably shorten its lifespan!
|
Product description The Pelco USRACK 4RU Fiber Rack Mount is a chassis for fiber optic modules, featuring an internal power supply. The chassis is designed to hold up to 14 single-width fiber optic modules. The internal power supply is 4 RU high. The chassis is designed to mount into an EIA-standard 19" rack. Optional single-width blank modules RACK1B (sold separately) can be inserted into empty module slots.The fiber card cage features automatic electronic current limiting at each module rather than limiting current at the power supply. If a fiber module fault occurs, only the faulty module will shut down. All other modules within the rack will continue to operate unimpaired. This features is also self-resetting, allowing the unit to handle a temporary, intermittent fault or overload. Modules in the chassis are hot-swappable, allowing the rack to remain powered when removing or replacing the modules. - Mounts in a EIA-standard 19" rack
- Holds up to 14 single-width fiber optic modules
- Hot-swappable internal power supply
- Voltage transient protection on all power and signal input/output lines
- Optional blank modules available (sold separately)
UPC: 700880297872 Table of Contents
|
Upload User Manual
Have you got an user manual for the Pelco USRACK 4RU Fiber Rack Mount With Internal Power Supply in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersPelco USRACK Specs | | | Input Voltage | 90 to 264 VAC at 70 W maximum | | Output Voltage | 9 VDC ± 5% at 6.5 A at 167°F (75°C) | | Fuse Rating | 1.25 A slow blow (rack power supply); plug-in modules are individually electronically fused; each power supply unit is individually fused | | Power Connector | 2-pin, for user-supplied power supply | | Power Indicators | Red LED | | Cord | AC Line: Detachable, IEC-connected; allows easy field replacement or exchange for various AC power cord configurations | | MTBF | >100,000 hours | | | | Operating Temperature | -40 to 167°F (-40 to 75°C) | | Storage Temperature | -40 to 185°F (-40 to 85°C) | | Operating Humidity | 20 to 80%, noncondensing | | Maximum Humidity Gradient | 10% per hour | | Operating Altitude | -16 to 3,048 m (-50 to 10,000 ft) | | Operating Vibration | 0.25 G at 3 Hz to 200 Hz at a sweep rate of 0.5 octave/minute | | Heat Dissipation | 240 BTU (full rack average) | | | | Rack Units | 3 | | Construction | Aluminum | | Mounting | Fits in a 19.00" (48.26 cm) EIA-standard rack | | Certifications & Ratings | CE, Class A
FCC, Class A
UL/cUL Listed
C-Tick
Designed to meet NEMA TS 1/TS 2 and Caltrans traffic signal control equipment environmental standards | | Dimensions (WxHxD) | 7.5 x 6.9 x 19.0" (48.2 × 19.0 × 17.5 cm) | | Weight | 4.35 lb (2.00 kg) | | | | Package Weight | 7.25 lb | | Box Dimensions (LxWxH) | 20.5 x 11.1 x 9.8" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 55 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
NEWER F100 CAMERA MONITOR...
PhotoStage progessional...
powerpint...
Night Detective Quest 5M 5x Night Vision Monocular ...
Ibanez AM93QM User Manual....
|
| Discussion |
Latest contributions to the discussion:
TR-P5TP pink robot dog
Name: Allyson
Top Race Race & Remote Control
Hello we are having issues with the remote to the robot dog it just flashes a red light will not sync to the robot dog what so ever the dog is charged and batteries have been changed out more the once, Can i get help trouble shooting the issue or if something needs to be sent bac...
Query
Name: Libba Guyton
Canon Pixma TS9520 Wireless All-In-One Printer
Support Code 1851
Multi purpose tray guide is open. Close the guide and press OK.
Done and the same message continue to appear....
Manual
Name: Grant
Konus KonuStart-700B 60mm f 11.6 Refractor
Please send user manual for Konustart-700B to above email address....
Fs3x manual
Name: Randy Reid
DigiTech FS3X Three-Function Foot Switch
I need manual
...
adding additional chime
Name: Stan Stansfield
OhmKat Video Doorbell Power Supply for
The additional chime does not work and is closure to the transmitter then the first one. I plugged in the additional chime and set the volume and chime. The original chime works when the additional chime is plugged in to new location. The original chime is located further away bu...
|
|
