|
User Manual for Platypod Max Camera Support with Multi Accessory Kit Click to enlarge the picture
Contents of the user manual for the Platypod Max Camera Support with Multi
- Product category: Counter, Chest & Strap Pods Platypod
- Brand: Platypod
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Platypod Counter, Chest & Strap Pods
|
User manual for the Platypod Max Camera Support with Multi contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Platypod product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Platypod user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Platypod product will considerably shorten its lifespan!
|
Product description The Max Camera Support with Multi Accessory Kit from combines the low-profile support with accessories that will help you stabilize and create photographs. Furthermore, you can attach different accessories with the included adapters to the camera support, place the support on smooth surfaces with the silicone pad, or secure onto a tree or pole with the 36" strap. - Platypod Max Camera Support The Platypod Pro Max Camera Support is a wide, stable, and ultra low-profile platform that allows you to set up a large tripod head, camera, and lens on both horizontal and vertical surfaces.
Measuring 5.3 x 7.8" and only 0.2" thick, the Pro Max Camera Support allows you to photograph or record with a camera that is elevated only slightly higher than the tripod head it is used with. Four reversible, spiked feet that each feature rubber tips on one end can be distributed among five strategically placed, 1/4"-20 threaded holes. Once installed, they can be adjusted to level the platform on uneven surfaces, both indoors and out. For placement on unconventional surfaces and angles, two 2-inch belt shots allow the Pro Max Camera Support to be secured to a cylindrical object or to be taped onto angled floors. Two nail holes are included for permanent or semi-permanent mounting to walls, boards or ceilings; and for quick placement and removal from conventional tripods or quick release devices, 1/4"-20 and 3/8"-16 threaded holes are on the underside of the platform.
When the spike feet and their locking nuts are not in use, a magnetized storage box holds them against the top of the Platypod Pro Max Camera Support. Able to hold up to 300 lb, the Platypod Pro Max Camera Support accepts tripod heads with 3/8"-16 mounts, and is constructed from anodized, aluminum-alloy for durability and corrosion resistance. UPC: 881314396801 - Platypod Multi Accessory Kit The Multi Accessory Kit from Platypod contains accessories that will help you stabilize and create photographs in combination with compatible Pro, Max, and Ultra tripod kits. In certain lighting situations, a side light is necessary to fill-in the shadows, and create the shot. The 3" long spigot adapter enables you to attach monolights or umbrella adapters to the spigot and onto a Platypod tripod. Moreover, sometimes a smooth surface may not be the ideal spot to place a tripod, but the 4 x 6", 2mm-thick silicone pad prevents the Platypod from slipping off the surface or even scratching it. The 1/2" tall riser with a 1/4"-20 male stud enables you to mount a camera or other device to the tripod without the use of a head. In addition, the anodized aluminum riser gives clearance to smaller tripods heads that would otherwise have its knobs bump into the bottom platform of a Platypod tripod. Also included is a 36" long and 1.5" wide tension strap that has a weight capacity of 100 lb, can loop through a compatible tripod kit, and can wrap and secure the tripod to any tree or pole. Therefore, you gain height instead of photographing from the ground. When the Multi Accessory Kit is not in use, the drawstring pouch keeps all your accessories secure and in one place.
- The spigot adapter enables you to attach a speedlight or monolight to the Platypod tripods
- 4 x 6" silicone pad lays under any of the Platypod tripods to prevent slipping or scratching on smooth surfaces
- 1/2" tall riser lets you attach a camera or other devices directly to a Platypod tripod. The riser also helps to give height, which prevents the head's knobs from bumping into the tripod's platform
- The 36" long Tension strap allows you to strap any of the Platypod tripods to a freestanding object, such as a tree or pole
UPC: 714983535526 In the Box - Max Camera Support dqewzqsacbzq
- 4 x Spike Screw Feet
- 4 x Spike Screw Feet Locking Nuts
- Storage Box for Spike Screw Feet
- Pouch
- Limited 5-Year Warranty
Table of Contents
|
Upload User Manual
Have you got an user manual for the Platypod Max Camera Support with Multi Accessory Kit in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parameters - Platypod Max Camera Support
| Material | Aluminum alloy | | Dimensions | 5.3 x 7.8" (13.5 x 19.8 cm) | | Thickness | 0.2" (5 mm) | | | | Box Dimensions (LxWxH) | 8.8 x 6.5 x 1.4" | - Platypod Multi Accessory Kit
| Material of Construction | Riser: Aluminum | | Finish | Riser: Black anodized | | Weight Capacity | Tension Strap: 100 lb (45.4 kg) | | Threads | Spigot: 1/4"-20 - 3/8"-16 female-to-female- Riser Tripod Mount: 3/8"-16
Riser Camera Mount: 1/4"-20 | | Dimensions | Spigot:
Length: 3" (76.2 cm)
Riser:
Diameter: 1.5" (38 mm)
height: 0.5" (13 mm)
Silicone Pad: 4" x 6 x 0.08" (102 x 152.4 x 2 mm)
Tension Strap (L x W): 36 x 1.5" (914 x 38 mm)
Drawstring Pouch (L x w): 6.25 x 4.25" (159 x 108 mm) | | | | Box Dimensions (LxWxH) | 8.8 x 4.4 x 1.5" |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 29 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
pocket quadcopter RIV-YT320...
CYBERPOWERPC GMA6200BSTV2...
FUJINON ERD-30A-D01A ZOOM DEMAND CONTROLLER
...
Just bought from Bestbuy Cyberpower,GMA5600BSTV4,model C series
another number on the label ET8252-10294
CECModel:CS450217MB492126 mfg date 043025
...
Vortex crossfire ii 6-24x50
I essentially want to return my scope to mechanical zero. This has been on a couple rifles and I would like to set f...
|
|
