|
User Manual for Pro Co Sound MBT-1 1:1 Microphone Bridging Transformer Click to enlarge the picture
Contents of the user manual for the Pro Co Sound MBT-1 1:1 Microphone
- Product category: Preamp Accessories Pro Co Sound
- Brand: Pro Co Sound
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Pro Co Sound Preamp Accessories
|
User manual for the Pro Co Sound MBT-1 1:1 Microphone contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Pro Co Sound product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Pro Co Sound user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Pro Co Sound product will considerably shorten its lifespan!
|
Product description The MBT-1 Microphone Bridging Transformer from Pro Co Sound is a carefully designed, custom-built 1:1 microphone bridging transformer whose characteristics are optimized for use with balanced low-impedance microphones or similar sources. Special winding techniques and a high-permeability (80% nickel) core lamination preserve full frequency response while minimizing signal losses and other "loading" effects. MU metal can and separate electrostatic shields for primary (input) and secondary (output) windings reduce capacitive coupling of ground-borne electrical noise between main and stage monitor or recording mixers, eliminating annoying 60-Hz hum and buzz. The source impedance of the MBT-1 is very similar to that of a low impedance microphone to ensure proper matching to the input circuitry of the mixer. The result is clean transient response (minimal overshoot or ringing) and low distortion even at low frequencies and high input levels. In the Box Pro Co Sound MBT-1 1:1 Microphone Bridging Transformer 9" Color-Coded Lead Limited 1-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Pro Co Sound MBT-1 1:1 Microphone Bridging Transformer in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersPro Co Sound PT1 Specs | | | Voltage Loss | <1.0 dB at 1.0 kHz All measurements made with 150 ohms source and 1.0 kOhms load to simulate typical real-world microphone and mic preamps (0 dBv ref = 0.775V). | | Input Impedance | >1050 ohms at 1.0 kHz
>1080 ohms at 10 kHz
Nominal source impedance is 150 ohms | | Source Impedance | Secondary:
<270 ohms at 1.0 khz
<300 ohms at 10 khz
Nominal output impedance is 1.0 kOhms | | Total Harmonic Distortion | <0.03% 20 Hz to 20 kHz at -30 dBv output
<0.1% 30 Hz to 20 kHz at -15 dBv output
<0.25% 20 Hz to 20 kHz at -15 dBv output | | Maximum Input Level | For 1% THD:
0 dBv at 20 Hz
+4 dBv at 30 Hz
+8 dBv at 50 Hz | | Frequency Response | 20 Hz to 20 kHz, ± 0.5 dB at -15 dBv output
-3 dB at approximately 65 kHz | | Phase Response | <-20° at 20 kHz (refer 1.0 kHz) | | Rise Time | <4.5 μs (2.0 kHz square wave, 10 to 90%) | | Overshoot | <1% | | Voltage | Common Mode:
>1500 VRMS (maximum) | | Common Mode Rejection | >80 dB at 1.0 kHz | | | | Turns Ratio | 1:1 | | Impedance Ratio | 150:150 ohms | | Primary Impedance | Source Impedance: 1.0 kOhm (typical microphone) | | Secondary Impedance | 1.0 kOhm (typical microphone preamp) | | Shield | Faraday Shield: 2 shields with separate leads | | Material | Core: 80% nickel alloy | | Maximum Input Level | At 20 Hz: 0 dBv (ref = 0.775 V) | | | | Package | MU metal can | | Termination | 9.0" (228.6 mm) 28 AWG tinned copper, color-coded leads | | Mounting | 2 holes, 0.09375" (2.3813 mm) diameter, 0.7185" (18.2499 mm) centers It is recommended to use only #4 Type-B self-tapping screws to mount transformer through mounting holes. They do not allow more than 0.15" of penetration into the transformer housing. | | Dimensions (L x W x H) | 1.125 x 1.125 x 1.050" (28.575 x 28.575 x 26.670 mm) |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 74 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Logitech MK850 Manual...
Swan Bread maker SWBBA7...
Expert intel sixcore i5-8400 4GHZ turbo...
Color LaserJet Pro MFP M281fdw...
call of duty world war II...
|
| Discussion |
Latest contributions to the discussion:
Query
Name: Geoff Dibblee
Carson zOrb Digital USB Microscope
when useing the zorb it will not cover the whole of a stamp back or front as i am useing it for perfins stamps and whati have recived in the box just covers half a letter please can you help me to find away to enlarg the whole stamp
...
Blown transformer
Name: Dik Schouten
Demeter VTDB-2 Single Channel Tube Direct
Dear Sirs,where can i buy a new transformer for my VTDB 2b? If possible een 230 volt primary site...Y.S. Dik Schouten
...
Battery charger light does not turn yellow or green when charging LP-E17
Name: DAVE
Canon LC-E17 Charger for LP-E17 Battery
I have a new Canon battery charger for EOS R10 Camera. It has lights that turn yellow and green when charging the Canon battery that came with the camera. But when I put in the BM battery LP-E17 no lights come on. I can tell the battery is charged when I put it in the camera, b...
Stiff center dial wheel
Name: Reynolds, Jane
Tasco 10x50 Essentials Porro Binocular
It is very hard for me to turn the center wheel with the ridges on it.
Could you please email me the user manual for the Tasco 10 x 50 mm zip focus? Thank you...
Redfield 2-7x33
Name: Mike
Redfield 2-7x33 Revolution Riflescope
Can the elevation and windage knobs be reset to zero?
Thanks!...
|
|
