|
User Manual for Propellerhead Software Synchronous Timed Effect Modulator Rack Extension for Reason Click to enlarge the picture
Contents of the user manual for the Propellerhead Software Synchronous Timed Effect Modulator
- Product category: Virtual Processor Plug-Ins Propellerhead Software
- Brand: Propellerhead Software
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Propellerhead Software Virtual Processor Plug-Ins
 |
User manual for the Propellerhead Software Synchronous Timed Effect Modulator contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Propellerhead Software product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Propellerhead Software user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Propellerhead Software product will considerably shorten its lifespan!
|
Product description Designed to be a modulation powerhouse, Synchronous from Propellerhead is a rack extension for Reason that offers four effects processors and three independent curves to create a wide range of effects including ambiances, pumping, stutter, and sweeps. Animate pads, wobble basses, or glitch-up samples. Draw complex modulation waveforms and assign them to the internal distortion, filter, delay, or reverb effects. Additionally, the curves can be routed simultaneously from the rear of Synchronous to any available device within the Reason rack, allowing for an even greater flexibility. Note: Note: Rack Extensions are only available for single-user licenses. This means that if you are a school/institution and have a multi-license for Reason, you will not be able to try, purchase or install Rack Extensions. - Interface and Controls
-
- The interactive display is where you draw the curves that drive Synchronous’ modulation effects. There are three independent curves that can target any mix of effect parameters.
- You draw the curves with the waveform tools. Pick a waveform, a resolution and start drawing. You can mix and match waveforms and resolutions within the same wave for even richer modulation options.
- For instant inspiration, load up any of the 100+ patches that comes packaged with Synchronous.
- Assign the curve to the desired effect parameter and set the amount. You can even let several curves control the same parameter.
- Distortion with four characters including Ring Modulation and Bit Crush.
- Multi-mode filter (low-pass, band-pass, high-pass and comb) with lag setting to smooth out filter modulation, if desired.
- Delay unit with roll and ping pong. Great for anything from rhythmic delays to stutter effects.
- Reverb unit that lets you modulate the reverb amount and decay times. You can switch between modulating the send amount or the return amount.
- Level for super-easy ducking effects, like the omnipresent pumping, four-on-the-floor sidechain ducking, simply let a curve control the output level from Synchronous.
- Patches
-
- In cooperation with renowned sound designer Nucleus Soundlab, Synchronous comes with 100+ versatile modulation patches across categories such as Ambience, Pumping, Stutter, Sweeps and builds and more. Also included is a set of Combinator patches with instruments that make good use of Synchronous.
- Rack Routing
-
- Aside from driving the built-in effects, Synchronous modulation engine can of course be routed to just about anything using Reason’s control-voltage connectors on the back side of the Reason rack. Use one curve to control the distortion amount on a Scream 4 distortion unit added to an audio track. Use another curve to add motion to a pad in Parsec by modulating engine parameters.
Table of Contents
|
Upload User Manual
Have you got an user manual for the Propellerhead Software Synchronous Timed Effect Modulator Rack Extension for Reason in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersPropellerhead Software 143856 Specs | System Requirements | Rack Extensions require Reason 6.5 or later, or Reason Essentials 1.5 or later
An active Internet connection is required to access the Propellerhead Shop and to install the Rack Extensions on your computer |
Rating90% users recommend this product to others. And what about you?
This product has already been rated by 73 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Jumpdrive C20i...
Pacsafe Travel Safe 200...
Narink Pro Food chopper B871 users manual...
manual for: "Battery Charger CG-580"...
Dawnstar Electric Knife Sharpener Model: S858-2 user ...
|
|
