|
User Manual for Quested SBC800 Powered LFE Sub-Bass and LCR Controller Click to enlarge the picture
Contents of the user manual for the Quested SBC800 Powered LFE Sub-Bass and
- Product category: System Processors Quested
- Brand: Quested
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Quested System Processors
|
User manual for the Quested SBC800 Powered LFE Sub-Bass and contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Quested product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Quested user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Quested product will considerably shorten its lifespan!
|
Product description The 800W SBC800 Powered LFE/Sub-Bass and LCR Controller from Quested is a bass management tool for music and film production designed to improve the low frequency response of surround sound or film monitoring systems. It has enough power and connectivity to support up to three X12 or X15 subwoofers (not included). Its back panel features individual LCR inputs and outputs as well as an LFE input, while its front panel provides adjustable controls of gain and phase for each section independently. The SBC800 provides EQ for all outputs and amplification for subwoofer outputs. The mono output is 800W into 4Ω and output level is monitored with an LED display. This unit is rack-mountable (2RU). - Adjustable controls for LCR, LFE, and PEQ sections
- Two bands of parametric equalization to adjust LF response to suit different applications
- 800W into 4Ω output level monitored with LED display
Table of Contents
|
Upload User Manual
Have you got an user manual for the Quested SBC800 Powered LFE Sub-Bass and LCR Controller in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersQuested SBC800 Specs | Connectors | 4 x XLR and 1/4" combination sockets, inputs female
3 x XLR outputs, male
2 pairs of 4 mm banana socket, speaker binding posts +/- , female
1 x 3.5 mm phone jack, system bypass link and remote switching, female
1 x IEC, power input | | Impedance | XLR and 1/4" Combination Sockets: 10 kΩ, electronically balanced
XLR Outputs: <100 Ω, electronically balanced | | High Pass Filter | -3 dB at 7 Hz, 24 dB/Oct | | Low Pass Filter | -3 dB at 100 kHz | | Controls | Left, Center, Right (LCR) Channel:
Phase: 0 - 180°
Frequency: 30 Hz - 90 Hz, adjustable crossover frequency
Bypass/Sub-Off: Switches LCR inputs directly to LCR outputs
Mix Level: -16 dB to +6 dB relative to LCR input
Low Frequency Effects (LFE) Channel:
Gain: -16 dB to +6 dB relative to LCR input
+10 dB Boost: Switched, for LFE input
Frequency: 50 Hz - 150 Hz, adjustable low pass filtering
Phase: 0 - 180°
Bypass: Switched, for LFE section
Parametric Equalizer (PEQ) Section:
Frequency: 20 - 90 Hz
Width: Q Factor 0.5/3.0
Gain: -6 dB to +6 dB
Phase/Polarity: 180° phase reversal
Sub Solo: Mutes all outputs except subwoofers | | Mono Output | 800 W @ 4Ω
400 W @ 8Ω | | Hum and Noise | <-105 dB (referred to clip level) | | THD | <0.03% at levels up to 1 dB below clip level | | Power Requirements | 115 / 230 VAC, 50/60 Hz | | Operation | 115 VAC (80 to 127 VAC maximum)
230 VAC (160 to 255 VAC maximum) | | Power Consumption | 45 W (quiescent current) | | Dimensions | 19.0 x 3.5 x 11.8" (48.2 x 8.8 x 30.0 cm) | | Weight | 23.1 lb (10.5 kg) |
Rating100% users recommend this product to others. And what about you?
This product has already been rated by 84 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
inspiron 3470...
Film Scanner 8 mm + super 8 REELS MOVIE MAKER PRO...
HP 3630 deskjet printer/scanner...
Dell KB216 ITALIAN Slim Office Multimedia Keyboard BLACK.
...
Mistral MC2300R 25L Detachable Air Coller with Steriliser.
Thank you in advance for your assistance.
Sincerely,
Jonathan Chua...
|
| Discussion |
Latest contributions to the discussion:
Provident aut voluptas.
Name: Ophelia Crist
Logitech Wireless Presenter R400
this product is perplexed....
Feedback regarding your services
Name: Jessica Parisian
Logitech Wireless Presenter R400
I tried to cremate it but got Turkish Delight all over it....
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
|
|
