|
User Manual for Serpent Audio Splice SA-76 MKII FET Compressor Click to enlarge the picture
Contents of the user manual for the Serpent Audio Splice SA-76 MKII FET
- Product category: 500 Series Serpent Audio
- Brand: Serpent Audio
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Serpent Audio 500 Series
|
User manual for the Serpent Audio Splice SA-76 MKII FET contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Serpent Audio product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Serpent Audio user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Serpent Audio product will considerably shorten its lifespan!
|
Product description 500 Series: Guide to Effects Read More The Splice SA-76 MKII FET Compressor from Serpent Audio comes with four compressor circuits in one unit. The mode switching feature allows you to easily switch between these circuits at the push of a button. The four circuit modes are Blueface mode (blue input circuitry and black output circuitry), the Blackstripe mode (black input circuitry and blue output circuitry), classic Blackface mode (black input and output circuitry), and classic Bluestripe mode (blue input and output circuitry). - Four compressor circuits in one unit
- Stereo linkable with front panel switch
- External send and return with front panel switch
- Slam mode (all buttons in) feature available via front panel switch
- True bypass (relay controlled) with front panel switch
- Mix/blend control knob with switchable bypassing for parallel processing
- Integrated active sidechain filters
- Switchable 600-Ohm output loading allows for easy optimization of the unit for use with both vintage and modern equipment
- 45 dB of gain (no limiting)
- True VU meter with meter buffer circuitry
- Integrated linear power supply
- Compatible with 115 or 230 VAC power input (user-selectable on rear panel)
In the Box Serpent Audio Splice SA-76 MKII FET Compressor Limited 2-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the Serpent Audio Splice SA-76 MKII FET Compressor in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersSerpent Audio Splice SA-76 MKII Specs | Function | Single-channel FET-based compressor | | Number of Channels | 1 x mono (stereo linkable) | | Inputs | 1 x constant 600-Ohm input attenuator, floating transformer balanced | | Outputs | 1 x floating transformer balanced
With Mix Function Enabled: < 100 Ohms output impedance, transformer-like floating output, electronically balanced (accepts balanced or unbalanced signals) | | Send | External: < 100 Ohms output impedance, transformer-like floating output, electronically balanced (accepts balanced or unbalanced signals) | | Return | External: 22 kHz input impedance, electronically balanced (TRS), (accepts balanced or unbalanced signals) | | Maximum Input Level | +30 dBu with compression engaged and input level knob set to max (fully clockwise) | | Compression Ratio | 2:1, 4:1, 8:1, 12:1, 20:1 | | Attack Time | 20 to 800 µs | | Release Time | 50 ms to 1.1 sec | | Maximum Output Level | +24 dBu | | Output Load | 150 Ohms minimal | | Gain Reduction | FET | | Make-up Gain | 45 dB (± 1 dBu) with compression disabled (ratio set to soft bypass) | | Frequency Response | 20 Hz to 20 kHz | | THD+N | Typically 0.5% | | Dynamic Range | Not specified by the manufacturer | | Signal-to-Noise Ratio | >80 dBu | | Power Supply | 115 / 230 VAC (integrated) | | Dimensions | 3.5 x 19 x 9.25" / 13.3 x 3.81 x 17.3 cm | | Weight | 10.1 lb / 4.6 kg |
Rating90% users recommend this product to others. And what about you?
This product has already been rated by 06 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
inspiron 3470...
Film Scanner 8 mm + super 8 REELS MOVIE MAKER PRO...
HP 3630 deskjet printer/scanner...
Dell KB216 ITALIAN Slim Office Multimedia Keyboard BLACK.
...
Mistral MC2300R 25L Detachable Air Coller with Steriliser.
Thank you in advance for your assistance.
Sincerely,
Jonathan Chua...
|
| Discussion |
Latest contributions to the discussion:
Provident aut voluptas.
Name: Ophelia Crist
Logitech Wireless Presenter R400
this product is perplexed....
Feedback regarding your services
Name: Jessica Parisian
Logitech Wireless Presenter R400
I tried to cremate it but got Turkish Delight all over it....
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
|
|
