|
User Manual for SPL Crossover - Active Analog 2-Way Crossover for Pro Audio and Hi-Fi Applications Click to enlarge the picture
Contents of the user manual for the SPL Crossover - Active Analog 2-Way
- Product category: Crossovers SPL
- Brand: SPL
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for SPL Crossovers
|
User manual for the SPL Crossover - Active Analog 2-Way contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any SPL product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official SPL user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a SPL product will considerably shorten its lifespan!
|
Product description Styled in black, the SPL Crossover is an active, analog 2-way crossover to coordinate your main speakers with your subwoofer, doing so without any DSP or analog-to-digital technology at all. The unit splits your signal, diverting midrange and high-range audio to your main monitors, and leaving the lows to route to the subs. The design utilizes SPL's 120V rail technology to ensure high headroom and crystal clear performance, and makes use of switches and pots to select among crossover frequencies, phase positions, low-level, and more. It's designed to work in both 2.1 and 2.2 setups, so if you utilize stereo subwoofers, this device will be suitable for your uses. The unit splits signal into two sections: Low and Mid-Hi, doing so at ranges from 50 to 120 Hz in 6 different steps. The roll-off frequency for the Mid-Hi section can be 12 or 24 dB for octave to better complement your set up. Time aligning the low-end is very important, and this can be done via the flip of a phase switch, or on a continuously variable basis, giving you a full 360° of phase options to select among. A low-cut filter is on hand to roll off frequencies below 20 Hz, which can be useful in keeping power amplifiers from trying to produce virtually inaudible frequencies that can cause sonic interference—and not a lot more. You can also vary the output of the subwoofer section on this device, doing so with a range of 20 dB. With the 3.5mm Control section, you can power up to four compatible power amplifiers straight from the Crossover, sending them 12V signals to switch them from stand-by to on. Low Section - General Controls
- In the Low section, you'll see controls for crossover frequency, level and phase. You can also select between operations for one or two subwoofers, depending on your setup.
- Output Switch
- If your playback system consists of two top speakers and a single subwoofer, set this switch to mono. The left and right channels are then summed to mono to feed the subwoofer. The mono LOW signal is then passed to both Low outputs, and you can select either one to drive your sub.
- Low X-Over Switch
- The Low crossover filter is a Linkwitz/Riley design. The roll-off is 24 dB per octave. Set the crossover frequency with this switch. Available crossover frequencies are: 50, 60, 70, 85, 100, and 120 Hz.
- Phase Section
- The PHASE switch and PHASE potentiometer time-align the subwoofer (or subwoofers) with the top speakers. This is especially useful when the subwoofer is placed elsewhere in the room. If you set the PHASE switch to position "Var -180°", you can use the phase potentiometer to vary the signal continuously between -180 and 0°. If you set the Phase switch to position "Var 0°", the potentiometer will operate between 0 to 180°.
- Level Knob
- Set the overall level of the subs with this potentiometer. The control has a range of ±10 dB. It allows you to finely control the level of your subs in relation to your top speakers.
Mid-Hi Section - General Controls
- The Mid-Hi section gives you various control over the frequency and roll-off of the top speaker's crossover.
- Crossover On/Off
- If you want to drive your top speakers full range, set this switch to off. The signal will then pass to the outputs without processing. Switch to on if you want to switch among frequencies with the X-Over and Roll-Off switches.
- X-Over Switch
- Select the crossover frequency for the mid-hi bands with this selector. You can choose among 50, 60, 70, 85, 100, or 120 Hz.
- Roll-Off Switch
- This switch can be set to two different slopes, 12 dB per octave (Butterworth), and 24 dB per octave (Linkwith/Riley).
- Low-Cut Switch
- With the Low-Cut switch, you can engage a cut filter for frequencies below 20 Hz. The roll-off is 12 dB per octave. Both the Low and Mid-Hi sections are affected by this filter. It is used to filter out frequencies that do not contain musical content but demand a lot of power from the power amplifiers.
- Amp Control I/O
- The Crossover sports 3.5mm inputs and outputs for triggering compatible units from standby to on, using a 12V trigger. If you own an SPL device that supports Amp Control outputs, you can trigger standby and operation of the Crossover. Just connect the Amp Control output of any compatible SPL device to the Crossover's Camp Control input. The Crossover has four trigger amp control outputs to switch up to four power amplifiers simultaneously. If the Crossover is triggered via Amp Control input section, the connected power amplifiers are triggered too. You may also use 12V trigger controller from third party developers. Use cables with 3.5mm mono mini jack plugs, where the tip is plus and the sleeve is minus.
In the Box SPL Crossover - Active Analog 2-Way Crossover for Pro Audio and Hi-Fi Applications (Black) Power Cable Limited 2-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the SPL Crossover - Active Analog 2-Way Crossover for Pro Audio and Hi-Fi Applications in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersSPL SPLCROSSOVER Specs | Connection | Balanced: 2 x XLR, Neutrik Connectors Unbalanced: 2 x RCA | Control Inputs | 1 x TS 3.5 mm | Impedance | Balanced: 20 kOhms (Approximate) Unbalanced: 10 kOhms (Approximate) | Maximum Level | Balanced: +32.5 dBu Unbalanced: +32.5 dBu | CMR | Balanced: -82 dBu at 1 kHz | | Connections | 4 x XLR 4 x TS 3.5 mm (Control Outputs) | Crosstalk | Low: -70 dB at 70 Hz Mid-Hi: -70 dB at 1 kHz | THD | Low: 0.0014% at 30 Hz Mid-Hi: 0.0008% at 1 kHz | Noise | Low: -104.9 dB (A-Weighted) Mid-Hi: -106.0 dB (A-Weighted) | Dynamic Range | Low: 136.9 dB Mid-Hi: 138.0 dB | Frequency Range | 50, 60, 70, 85, 100, or 120 Hz to 300 kHz (-3 dB) | | Operating Voltage | Analog: ±60 V, Internal Operating Voltage | Mains Voltage | 115 VAC / 60 Hz or 230 VAC / 50 Hz | Fuses | 230 V: T 630 mA 115 V: T 1.2 A | Power Consumption | 50 VA, Maximum | Standby Power Consumption | < 0.1 W | Dimensions (W x H x D) | 10.9 x 3.9 x 13.0" / 278.0 x 100.0 x 330.0 mm (Including Feet) | Weight | 11.9 lb / 5.4 kg |
Rating70% users recommend this product to others. And what about you?
This product has already been rated by 81 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
Trijacon ACOG USMC scope... Pyle Pro BTA 62BT 6-Zone Stereo Receiver Bluetooth... LG Gram 17 Laptop... LG 300W 2.1 ch surround sound manual. It has the soundbar, subwoofer, wireless receiver for connected rear speakers and wireless controller. ... Konus KonuSpot-60C 20-60x60 Spotting Scope...
|
Discussion |
Latest contributions to the discussion:
Settings access and setup Name: Edwin Derks Nuance PaperPort 14 I had a problem with Paperport loading. Through the remote efforts of a Tech was able to get back online, however, "settings" are only listed 1 - 5 with no action listed as was 'visibly' available, (i.e. Scan both sides, Black and White, Color, etc.)
1. how to change, 2. wha... query Name: Vudayagiri Balasubramanyam Bose Wave SoundTouch Music System IV how to set up my bose radio with my remote working-class ... Hi. I didn’t even get a chance to try it once! :( plz help Name: Eric Tasakovic Keeley Dark Side Pedal I ordered a dark side pedal second hand online for 20 bucks cheaper than it would have been to buy it new….20 measly bucks. Anyway…it didn’t come with a power supply. I messed up and accidentally plugged in a 9v ac output power supply in, instead of the required 9v dc. I’... Conectare wi-fi Name: Zazuleac Gheorghe ezviz CV-206 Mini O 720p Wi-Fi Cv ezviz nu se conecteaza la router upc.... Conectare wi-fi Name: Gheorghe Zazuleac ezviz CV-206 Mini O 720p Wi-Fi Nu pot conecta cv wi-fi ezviz la router upc- vodafone....
|
|