|
User Manual for TC-Helicon Ditto Microphone Looper Click to enlarge the picture
Contents of the user manual for the TC-Helicon Ditto Microphone Looper
- Product category: Vocal Processors TC-Helicon
- Brand: TC-Helicon
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for TC-Helicon Vocal Processors
|
User manual for the TC-Helicon Ditto Microphone Looper contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any TC-Helicon product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official TC-Helicon user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a TC-Helicon product will considerably shorten its lifespan!
|
Product description TC-Helicon's Ditto Microphone Looper uses just two switches for building loops with a five-minute maximum initial loop time and unlimited overdubbing. It has a built-in microphone preamp with phantom power and delivers your loops in 24-bit uncompressed audio. With Automatic Mic Gain, you set your input gain only once at the mixer for balanced loop levels.
You can use the Ditto in one of two modes. In Mic Control, all functions of the looper can be controlled using the button on the TC-Helicon MP-75 or the Sennheiser e835fx mic. In Normal mode, you can use any dynamic or condenser mic and control the looper using the footswitches.
The Ditto Looper offers two workflow modes. In Default mode you press the footswitch to record your initial loop, press it again to play it back, then press it a third time for overdubbing. In Alternate mode, you record your initial loop, then press the footswitch to start overdubbing immediately. You can also restore your last deleted take during playback, and when erasing your last take, previously recorded material remains. The loop level knob controls the playback level and the LED indicates five modes – Record, Play, Erase, Loop in Memory, and Loop at Beginning Point.
You can use the Ditto Looper not only with vocals but also with other mic'd instruments. The Ditto could be especially useful to solo musicians interested in adding more layers to their sound. It has an XLR output for connecting to a PA and is Mac/Windows-compatible for firmware downloads. - Automatic mic gain for balanced loop levels
- Control looper from the TC-Helicon MP-75 or the Sennheiser e835 microphones
- Use dynamic or condenser microphones
- Mac/Windows-compatible firmware
In the Box TC-Helicon Ditto Microphone Looper USB Cable Limited 10-Year Warranty Table of Contents
|
Upload User Manual
Have you got an user manual for the TC-Helicon Ditto Microphone Looper in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersTC-Helicon 996365005 Specs | Controls | Loop level knob
Loop record/play/overdub
Loop stop/erase switch | | Settings | Loop record/play/overdub
Loop record/overdub/play | | Analog Input | Input: XLR female, balanced
Input Impedance: 2.7 kOhms balanced
Maximum Input Level: -1 dBu
Signal to Noise Ratio: 112 dB A-weighted
Phantom Power: 32 V (always on) | | Analog Output | Output Connector: XLR male, balanced
Output Impedance: 250 Ohms balanced
Maximum Output Level: -1 dBu
Dynamic Range: > 104 dB, 20 Hz to 20 kHz
Frequency Response: 0 / -0.3 dB, 20 Hz to 20 kHz
USB connector type: Mini-B USB | | Control | Microphone control using TC-Helicon MP-75 or Sennheiser e835 FX microphones | | Indicators | 1 x LED | | Power | Power supply 12 V, 400 mA (center negative)
Power consumption: 5.6 W | | Construction Material | Two-part die-cast metal
Rubberized base | | Dimensions (H x W x D) | 5.4 x 3.5 x 2.3" / 137.2 x 88.9 x 58.4 mm | | Weight | 0.9 lb / 0.4 kg | | | | Package Weight | 1.6 lb | | Box Dimensions (LxWxH) | 6.6 x 5.7 x 3.3" |
Rating60% users recommend this product to others. And what about you?
This product has already been rated by 34 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
| Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
inspiron 3470...
Film Scanner 8 mm + super 8 REELS MOVIE MAKER PRO...
HP 3630 deskjet printer/scanner...
Dell KB216 ITALIAN Slim Office Multimedia Keyboard BLACK.
...
Mistral MC2300R 25L Detachable Air Coller with Steriliser.
Thank you in advance for your assistance.
Sincerely,
Jonathan Chua...
|
| Discussion |
Latest contributions to the discussion:
Provident aut voluptas.
Name: Ophelia Crist
Logitech Wireless Presenter R400
this product is perplexed....
Feedback regarding your services
Name: Jessica Parisian
Logitech Wireless Presenter R400
I tried to cremate it but got Turkish Delight all over it....
Instructions for assembling the 2015 Forecast Image Master Consoles GC3-A
Name: mike elam
Forecast Consoles GC3-A ImageMaster Editing Console
Looking for instructions for assembling this console. ...
EMPTY TONER ERROR MESSAGE AFTER REPLACING TONER
Name: LINDA BAD YELLOW EYES
Brother TN223BK Standard-Yield Toner
I HAD TO CHANGE OUT ALL THREE TONERS DUE TO LEAKS IN THE YELLOW AND CYAN. AFTER I REPLACED THEM, THE MACHINE KEEPS GIVING ME AN EMPTY TONER ERROR MESSAGE. HELP!!...
PS480D 20/24 pin Switching 480W Power Supply
Name: swkargo
Logisys 480W Power Supply
This item states in can run -5vdc .It is NOT listed on the board or I beleive is r4 is missing the resitior. Any body have thid issue. Shawn
...
|
|
