User Manual for Waves Scheps Omni Channel - Channel Strip Plug-In Click to enlarge the picture
Contents of the user manual for the Waves Scheps Omni Channel - Channel
- Product category: Virtual Processor Plug-Ins Waves
- Brand: Waves
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Waves Virtual Processor Plug-Ins
|
User manual for the Waves Scheps Omni Channel - Channel contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Waves product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Waves user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Waves product will considerably shorten its lifespan!
|
Product description Available for download, the Waves Scheps Omni Channel is a plug-in designed to handle all of your channel-strip needs. Channel-strip plug-ins take their inspiration from the individual channels of large-format mixing consoles, on which you’d often find an EQ, a compressor, and a gate/expander module. These processes could frequently be swapped in order, but the effect was always one of efficiency, getting you closer to the sound you want without having to patch in external gear. Many plug-ins have operated with this concept in mind, but the Scheps Omni Channel brings some new features into the mix that help you create more realized sounds with just one plug-in instance.
The preamp section, for instance, features a switchable saturation circuit with three types of harmonic distortion. Low- and high-pass filters are on hand to shave off unnecessary frequencies within the preamp. A four-band equalizer section features shelving and parametric bands. Next, you’ll note the DS² section, a processor with its genesis in both traditional split-band de-essing and dynamic equalization. You can use this module to de-ess a vocal, to notch out unpleasant resonances in snare drums, or for any other dynamic/frequency-specific need. A gate/expander is also available, as is a compressor with three different circuit types for eliciting different timbres. Further expanding the Omni Channel’s functionality, an insert slot allows you to patch in any Waves plug-in you desire, be it a delay, a modulator, or even an additional Omni Channel module.
The modules can be moved around in any order you wish, so you can apply preamp saturation after equalization if that’s the vibe of the track. The software can be used in mixing applications, but zero-latency operation and control-mapping for eMotion LV1 Mixing Consoles makes this plug-in a good choice for FOH engineers. The Scheps Omni Channel Strip is compatible with Mac and Windows platforms, and operates in AAX, AU, Audiosuite, VST, and VST3 formats. - Preamp Module
- The Pre module provides three types of analog saturation, letting you add diverse colors of harmonic distortion as well as filters and thump (resonance) controls.
- Compression Module
- The Compression module features 3 completely different compressors ranging from fast to slow and smooth, with a unified control set so you can quickly compare them. A Wet/Dry control allows you to use parallel compression within the module.
- EQ Module
- The EQ module is a four-band equalizer. Each band provides a distinct musical sound that holds up on its own or can be switched to be fully parametric if surgical EQ is required.
- DS² Module
- The DS² module is more than a de-esser. With two full-range bands and four filter types, it allows you to remove any offending frequencies, not just sibilances.
- Gate/Expansion Module
- The Gate/Expansion module gives you all the standard controls (threshold, attack, and release) for gating and expansion, but also lets you adjust the maximum noise reduction to maintain a consistent noise floor.
- Insert Slot for Additional Waves Plug-Ins
- The Scheps Omni Channel features an insert slot. It can be positioned anywhere in the chain. You can use the slot to insert an additional Waves plugin of your choice, including an extra instance of Omni Channel modules.
- Stereo or M/S Operation
- All modules can be operated in stereo or M/S mode, so you can EQ the sides differently from the center, compress the center and leave the sides alone, and more.
- Other Features at a Glance
-
- Designed with Grammy-winning mixer Andrew Scheps (Adele, Jay Z, Metallica, Red Hot Chili Peppers)
- Drag and drop any module anywhere in the channel strip
- Internal MS/Duo/Stereo routing per module
- Stereo component provides full discrete control over each channel
- Flexible shaping of internal or external sidechain input
- Zero-latency operation
- Focus presets designed by Andrew Scheps
- Artist presets by Tony Visconti, Billy Bush, Ken Pooch Van Druten, and others
Table of Contents
|
Upload User Manual
Have you got an user manual for the Waves Scheps Omni Channel - Channel Strip Plug-In in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parametersWaves Scheps Omni Channel - Specs | Mac Requirements | macOS 10.10.5 or laterCPU
Intel Core i5 / i7 / Xeon
Memory
8 GB RAM
8 GB free hard-disk space
Screen Resolution
Minimum: 1024 x 768
Recommended: 1280 x 1024 / 1600 x 1024
USB displays are not supported as the primary display.
Support for Visually Impaired Users
macOS Sierra 10.12.4
VoiceOver Utility enabled
Pro Tools 12.7
Logic 10.3.1 | | System Requirements (Windows) | Windows 7 with SP1, 64-bit
Windows 8.1, 64-bit
Windows 10, 64-bitCPU
Intel Core i3 / i5 / i7 / Xeon / AMD Quad-Core
Memory
4 GB RAM
8 GB free hard-disk space
Screen Resolution
Minimum: 1024 x 768
Recommended: 1280 x 1024 / 1600 x 1024 | | Supported Plug-In Formats | AU, VST, VST3, AAX, Audiosuite, | | Sample Rate | Supports up to 96 kHz | | Operation | Mono, stereo |
Rating80% users recommend this product to others. And what about you?
This product has already been rated by 27 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
