|
User Manual for Yongnuo YN860Li Speedlite Wireless Flash Kit for Nikon Cameras Click to enlarge the picture
Contents of the user manual for the Yongnuo YN860Li Speedlite Wireless Flash Kit
- Product category: On Camera Flashes Yongnuo
- Brand: Yongnuo
- Description and content of package
- Technical information and basic settings
- Frequently asked questions – FAQ
- Troubleshooting (does not switch on, does not respond, error message, what do I do if...)
- Authorized service for Yongnuo On Camera Flashes
|
User manual for the Yongnuo YN860Li Speedlite Wireless Flash Kit contain basic instructions
that need to be followed during installation and operation.
Before starting your appliance, the user manual should be read through carefully.
Follow all the safety instructions and warnings, and be guided by the given recommendations.
User manual is an integral part of any Yongnuo product,
and if it is sold or transferred, they should be handed over jointly with the product.
Following the instructions for use is an essential prerequisite for protecting
health and property during use, as well as recognition of liability on the part of the manufacturer
for possible defects should you make a warranty claim. Download an official Yongnuo user manual in which you will find instructions on how to install, use, maintain and service your product.
And do not forget – unsuitable use of a Yongnuo product will considerably shorten its lifespan!
|
Product description A Guide to On-Camera Flash Read More This Yongnuo YN860Li Speedlite Wireless Flash Kit for Nikon from gives you everything you need to start shooting with a multi-light setup. It bundles a pair of Yongnuo YN860Li flashes with a wireless transmitter for remote triggering in addition to a set of rechargeable batteries, battery charger, battery case, and a softbox. - 2 x Yongnuo YN860Li Lithium Speedlite With a guide number of 60' at ISO 100 and 200mm, this YN860Li Lithium Speedlite from Yongnuo is a portable lighting option for those that do not require TTL functionality. Built into it is a wireless transceiver, allowing it to be fired remotely at distances of up to 328' or used as a master to directly control the mode and output of compatible flashes. Additionally, it can also be used as an optical slave for multi-flash setups without radio transmission. The speedlight offers a wide zoom range of 24 to 200mm, with the ability to have its wide panel pulled out for an ever wider spread and softer light quality. The YN860Li runs on a rechargeable 1800mAh lithium-ion battery, lending it a fast recycle time that does not exceed 1.5 seconds as well as the ability to fire 700 full-power pops per charge. High-speed continuous shooting is supported, and the flash also boasts a multi mode for configuring a stroboscopic effect. The entire unit rotates 270° horizontally and tilts 90° up for easy bouncing in nearly any direction. Flash durations from 1/200 to 1/20,000 are possible depending on settings.
- Wireless Features
-
- When used as a master, can directly control the flash mode, flash output, stroboscopic settings, and focal length of YN860Li, YN660, YN560IV, YN560III, or YN968N
- When used as a slave, can receive triggering signal from YN860Li, YN560IV, YN660, YN560-TX II, RF605, RF603 II, and RF-602
- 16 channels and 6 groups for multi-flash programming
- Other Features
-
- Eight power levels, from 1/1 to 1/128
- LCD panel for viewing settings, controlled via dial and six buttons
- Two optical slave modes: S1 for synchronous firing, S2 to skip pre-flash
- Color temperature of 5600K, can be used outdoors in daylight without creating notable color casts
- Standard PC port for wired connection
- Overheat protection to keep equipment safe during heavy use
- Firmware upgrades available by connecting to computer via USB port
- Protecting bag and mini stand included for ease of use
- Yongnuo YN560-TX II Manual Flash Controller for Nikon Cameras Remotely control and trigger a variety of flashes and radio receivers all from the YN560-TX II Manual Flash Controller from Yongnuo. Designed to work with Nikon cameras, this transmitter is compatible with a variety of equipment, including YN560 III, YN560 IV, YN660, YN968, and YN860Li Speedlites and the RF602, RF603, RF603 II, and RF605 transceivers. This updated model is equipped with a redesigned LCD menu and a quick-locking foot. Using a 2.4 GHz frequency radio with a range of 328' and a choice of 16 channels, the YN560-TX II is able to reliably trigger your flashes from impressive distances. Also, it has remote power control and zoom control from 24-105mm for flashes set up within the six available groups. Additionally, it has a 2.5mm sync port and runs on two AA batteries.
- Vello Softbox for Portable Flash (Large, 8 x 12") Reduce the harshness of your on-camera flash unit and soften shadows by equipping it with this large Softbox for Portable Flash from Vello, which measures 8 x 12". This convenient modifier produces a soft, almost wrap-around quality of light that is useful in a wide variety of situations, such portraiture, weddings, food, and more. . It also features a foldable inner diffuser for further softening of the light and a reflective silver interior that evenly distributes light while maintaining maximum light output.
Setting up the softbox is simple with an integrated elastic strap with a touch tab fastener that secures around the flash head. Also, it has a strap loop and rubberized mounting tabs that will ensure that the softbox remains securely attached. When not in use, the modifier will fold down flat, and a zippered carrying case is included for travel and storage. UPC: 847628588400 - Watson MX AA NiMH Batteries (8-Pack, 1.2V, 2550mAh) Power various electronics, including photo equipment, flashlights, gaming devices, and more, with this 8-pack of 1.2V MX AA NiMH Batteries from Watson. The Japanese-made cells come pre-charged and ready for use with a capacity of 2550mAh, making them ideal for use in high-drain devices. Thanks to their very low self-discharge rate, they are capable of retaining up to 85% of their capacity after 1 year in storage. The batteries can be recharged up to 500 times before their usable capacity starts to diminish. Additionally, they are durable enough to function in temperatures as low as -4°F. UPC: 847628596856
- Watson 4-Hour Rapid Charger for AA and AAA NiMH and NiCd Rechargeable Batteries The 4-Hour Rapid Charger for AA and AAA NiMH and NiCd Rechargeable Batteries from Watson charges two or four AA or AAA batteries (not included). It is compatible with both NiMH and NiCd batteries. Charging time varies from 100-280 minutes, depending upon battery quantity, size, and capacity.
The charger's intelligent Negative Delta-V microprocessor doles out the full charge to each battery, while Zero Slope Detection prevents overcharging. The Safety Guard Timer automatically shuts off after 6 hours in cases where batteries are taking far longer than normal to charge, in order to prevent damage from excessive current. The charger has two charging level indicator lights to keep you apprised of battery status. Switching 100-240 VAC input power enables use all over the world. The charger's compact outlet prongs fold in, making the unit more compact for storage. - Will charge either 2 or 4 AA or AAA batteries (sold separately).
- Works with batteries that have Nickel-Metal Hydride (NiMH) or Nickel-Cadmium (NiCd) chemistry.
- Charging time varies based upon battery quantity, size, and capacity. Charging 2 AAA batteries will take about 100 minutes, while 4 AAA's will require about 200 minutes. Charging time for 2 AA batteries with a capacity of about 1800mAh will be roughly 110 minutes, while 4 AA batteries at that capacity will require about 220 minutes. For higher-capacity AA's in the 2400-2500mAh range, 2 batteries will charge in approximately 140 minutes, and 4 batteries will take about 280 minutes.
- An intelligent Negative Delta-V microprocessor ensures that each battery is charged to its full capacity, while the Zero Slope Detection feature prevents overcharging.
- Safety Guard Timer will automatically shut off after 6 hours. So in cases where batteries are taking far longer than normal to charge, they will not be exposed to excessive current that could cause damage.
- Dual charging level indicator lights are red while batteries are charging and turn green when charging is complete. They will flash red if the batteries are not charging properly.
- Switching 100-240 VAC input power allows you to use the charger all over the world.
- The compact outlet prongs fold in and out to make the unit smaller for easier storage.
UPC: 847628532953 - 2 x Watson Case for 4 AA or AAA Batteries (Black) This plastic Watson Battery Storage Case holds up to 4 AA or AAA batteries in dedicated slots. It has a compact form factor for easy storage in your pocket or a small compartment in your gear bag. The case has a snap closure and features an attachment point for connecting a second identical case, which could in turn be connected to another to create a chain, giving you an easy expansion option for storing more batteries. UPC: 847628006782
In the Box - 2 x YN860Li Lithium Speedlite zvuwyzzfcaxvutvxfurxfxrurdxzqys
- Protecting Bag
- Mini Stand
- YN-B1800 Rechargeable Li-Ion Battery (11.1V, 1800mAh)
- Battery Protective Case
- Charger
- AC Adapter
- Limited 1-Year Warranty
- YN560-TX II Manual Flash Controller for Nikon Cameras zvuwyzzfcaxvutvxfurxfxrurdxzqys
- Vello - Softbox for Portable Flash (Large, 8 x 12")
- Watson - MX AA NiMH Batteries (8-Pack, 1.2V, 2550mAh)
- Watson - 4-Hour Rapid Charger for AA and AAA NiMH and NiCd Rechargeable Batteries
- 2 x Watson - Case for 4 AA or AAA Batteries (Black)
Table of Contents
|
Upload User Manual
Have you got an user manual for the Yongnuo YN860Li Speedlite Wireless Flash Kit for Nikon Cameras in electronic form? Please send it to us and help us expand our library of instruction manuals.
Thank you, too, on behalf of other users.
To upload the product manual, we first need to check and make sure you are not a robot. After that, your "Submit Link" or "Upload File" will appear.
Technical parameters - 2 x Yongnuo YN860Li Lithium Speedlite
Mount | Shoe | Guide No. | 60' / 18.29 m ISO 100 at 200 mm Position | Exposure Control | Manual | Vari-Power | Manual: 1/1 to 1/128 | Bounce Head | Yes, -7 to +90° | Swivel Head | Yes, 270° | Coverage | 24 - 200 mm | Off-Camera Terminal | PC | Recycle Time | Approximately 0 to 1.5 Seconds | Flash Duration | 1/200 to 1/20000 sec | Flash-Ready Indicator | Yes | Slave Timing Modes | Instant Sync Skip Preflash | Wireless Operation | Method: RF Distance: Up to 328.08' / 100 m Mode: Master, Slave Method: Optical Pulse Distance: Up to 82.02' / 25 m Mode: Optical Slave | Wireless Communication Channels | 16 Channels | Wireless Groups | 6 Groups | Power Source | 1 x Proprietary Rechargeable Li-Ion Battery | Dimensions (W x H x D) | 3.0 x 8.1 x 2.2" / 7.5 x 20.6 x 5.6 cm | Weight | 14.25 oz / 404 g | | Box Dimensions (LxWxH) | 8.7 x 6.1 x 3.7" | - Yongnuo YN560-TX II Manual Flash Controller for Nikon Cameras
| Channels | 16 | Groups | 6 | Wireless Range | 328' / 100 m | Radio Frequency | 2.4 GHz | | Dimensions | 2.8 x 3.8 x 1.7" / 70 x 97.5 x 43 mm (Transmitter) | Weight | 3.5 oz / 99.2 g | | Box Dimensions (LxWxH) | 4.0 x 3.1 x 2.4" | - Vello Softbox for Portable Flash (Large, 8 x 12")
Modifier Type | Softbox | Attachment Method | Strap | Dimensions | H: 8.0 x W: 12.0" / H: 20.0 x W: 30.0 cm | Weight | 4.0 oz / 113 g | | Box Dimensions (LxWxH) | 12.9 x 9.1 x 0.9" | - Watson MX AA NiMH Batteries (8-Pack, 1.2V, 2550mAh)
| Battery Type | 8 x AA | Battery Chemistry | NiMH | Battery Voltage | 1.2 V | Capacity (mAh) | 2550 mAh | | Box Dimensions (LxWxH) | 5.984 x 2.756 x 0.551" | - Watson 4-Hour Rapid Charger for AA and AAA NiMH and NiCd Rechargeable Batteries
| AC Input Power | 100 to 240 VAC, 50 / 60 Hz | Power Consumption | 10 W | Charging Bays | 4 x AA, AAA | Supported Battery Chemistry | Ni-Cd, Ni-MH | Charging Voltage | 2.8 VDC | Charging Amperage | 500 mA | Power Input | 2-Prong US Plug | Charger Dimensions | 4.3 x 2.7 x 1.3" / 109.00 x 69.00 x 33.00 mm | Charger Weight | 2.8 oz / 79.4 g | | Operating Temperature | 32 to 113°F / 0 to 45°C | | Box Dimensions (LxWxH) | 5.3 x 4.0 x 1.4" | - 2 x Watson Case for 4 AA or AAA Batteries (Black)
Battery Type | 4 x AA, AAA | Material | Plastic | Closure Type | Snap Fastener | Dimensions (W x H x D) | 2.5 x 2.0 x 0.5" / 6.3 x 5.1 x 1.3 cm | Weight | 0.4 oz / 11 g | | Box Dimensions (LxWxH) | 2.0 x 2.0 x 1.0" |
Rating70% users recommend this product to others. And what about you?
This product has already been rated by 01 owners. Add your rating and experience with the product.
Discussion
Ask our technicians if you have a problem with your settings,
or if anything is unclear in the user manual you have downloaded.
You can make use of our moderated discussion.
The discussion is public and helps other users of our website who may be encountering similar problems.
The discussion is empty - enter the first post
Post a new topic / query / comment:
|
|
|
Request for user manual |
You can’t find the operation manual you are looking for? Let us know and we will try to add the missing manual:
I’m looking for a manual / Request for manual
Current requests for instruction manuals:
looking for a user manual for Quickbooks Premier Nonprofit 2020 for a Disabled American Veterans office.... Bower SFD9260.... 4-IN-1 WIRELESS CHARGER
... Brand :Gemini,model # XGA 4000,AND IT WAS PURCHASED NEW IN 2022,OR POSSIBLY EARLY 2023.WORKED perfect till one day I hit power switch and blew fuse x2... ZZSTAR binoculars...
|
Discussion |
Latest contributions to the discussion:
Will not reopen Name: Brian PNY Technologies 32GB Turbo 3.0 USB Thum drive will not open after not completely closing and extracting. ... v18 Name: Craig Mcinturff Davis & Sanford Provista 7518B Tripod I am looking for a camera mounting plate for a v18 fluid head Davis & Sandford ... Impact SF-ABRL160 Flash stopped working Name: Sarah sananes Impact SF-ABRL160 Stand Mount Flash with Hello, our flash is connected to a canon camera and all of the sudden the flash is no longer working.
Does the flash have a certain battery life? ... REPEAT REQUEST AS YOU DID NOT ANSWER YOU JUST SENT ME MY MESSAGE BACK -PLEASE HELP Name: Tish Hopkins Benro TAD37C Series 3 Adventure Carbon Hi again-- all this did was send this email back to me with a link that brought me right back here... what is this?? also a link to search for manuals-- ive been there done that there is NO Manual to be found that answers my ? Please HELP thanks!!
Hi there is an extra small sc... Tripod heads DO NOT sit flush on the plate of the tripod Help Please Name: Tish Hopkins Benro TAD37C Series 3 Adventure Carbon Hi there is an extra small screw on the plate that the tripod head screws on that prevents my gimbal tripod head from sitting flush when it is screwed on. this is very annoying and does not allow my camera to stay steady when shooting. Please tell me how to resolve this issue. th...
|
|